15 Reasons You Shouldn't Be Ignoring Timber Sash Windows Cambridge Door Hinge Repair Cambridge

Door hinges are an insignificant element that can have significant impact on the performance and appearance of your doors. Replacing squeaky hinges is a cheap and quick upgrade that can boost your home's curb appeal.

One method of fixing door hinges that sound squeaky is to make use of bar soap or petroleum jelly. Rub the item on the hinges to coat it.

Replacement Hinges

Hinges are a minor component that can cause a substantial amount of damage if they break or wear out. The good news is that hinges are simple to replace and don't require any special tools. It's important to choose the appropriate hinge for your home. This will help ensure that your door opens and closes smoothly. If your hinges for your door are not functioning correctly, get a professional to repair them as soon as you can.

A faulty hinge can cause the door to warp or pull away from the frame. This is typically caused by improper use or weight too much. To stop this from happening, it is important to lubricate your hinges. This will stop the hinge from becoming damaged or rusty, and will extend the lifespan of your door.

There are many different kinds of hinges. Each type has its own advantages and drawbacks. The most basic hinge is the butt joint which is secured to the door with a pin on each side. This type hinge is suitable for doors with light weights because it doesn't require a lot of strength to open and shut. The butt joint is more susceptible to damage than any other hinge.

It's best to use continuous piano hinges for doors that are heavier. This type hinge is fixed to the door and runs the full length of the door which allows it to open and close easily. This kind of hinge has the advantage of not needing the use of a center support and is more robust.

Another type of hinge is the storefront door pivot hinge, which allows doors to pivot from one location at the top and bottom of the door. These hinges are usually found in commercial buildings and are hard to repair if damaged. Experts can assist you by installing an entirely new pivot or replacing the old one. Depending on the type of hinge you choose, the cost will vary.

Loose Hinges

When hinges are loosened the door will hang in a crooked manner and could even begin to scrape the floor. This can be very irritating. With a few simple tools, any homeowner can fix hinges that are loose. In most instances, tightening the screws on the hinges will resolve the problem. However, in certain instances, the screws may have been stripped and they won't stay tight. If the screws have become soiled, you'll need to bore them and then plug them with wooden dowels or glue-coated matches made of wood.

To prevent your door hinges from becoming loose, it's important to ensure that they are lubricated and tightened regularly. Examine for any signs of damage on the hinges. If window replacement cambridge see any chips or cracks in the metal, this can be an indication that it's time to replace the hinge. It's also an ideal idea to replace the hinges when you notice that they are starting to bind or stick when you open and close the door.

The most common reason for hinges breaking is wear and tear due to constant use, without proper lubrication or tightening. This is true especially for doors that are frequently used by children. They may hang on handles of doors or even swing on hinges. This puts a lot of unnecessary stress on the hinges, which can result in them becoming loose and eventually falling off completely.

If the hinges are loose, you can tighten them up using a screwdriver. However when the hinges are loose for an extended period of time the constant movement of the hinge plate and screws will begin to create larger holes in the area where screws go. This can make it impossible for the screws to stay in place and they will eventually be stripped, rendering them useless. To fix this, dip the bare end a match made of wood in regular carpenter glue and tap it using a hammer. This will work the glue as far into the hole as it can. It is likely that you will need to use several matches that are coated with glue to fill in the hole.

Rusty Hinges

Rust is a typical issue for hinges on doors, particularly on older doors. It can cause the hinges to look shabby, but it can also cause them to break and fail. This can be an issue for those who use the door. It is possible to save an old hinge with a bit of work. The first step is to remove hinges and cleaning them to eliminate any gunk. After the hinges have been cleaned they can be oiled before being used again.

In the past hinges of poor quality were made of steel and iron that were prone to rust, but modern doors are often made of brass or metal alloys that don't rust as easily. Some people choose to use hinges from the past due to their beauty and durability. However they are more susceptible than modern ones to rust. The best way to avoid this is by preventing the hinge from rusting in the first place.

It is simplest to clean your hinges frequently by using steel wool and water, particularly when they are damp. If you do this frequently, rust won't be as much of an issue for your door hinges.

If you want to go one step further, you can use stainless steel hinges. In contrast to iron, stainless steel doesn't get rusty and can provide your home with modern look. If you aren't able to change the hinges on your existing door, however the best method to stop corrosion is to keep it away from your door hinges by periodically scrub them clean and then lubricating them.

It is best to take the hinges off completely to remove any rust that has accumulated. Once the hinges are clean and dry, you can apply a mix of oil and vinegar to further lubricate them and aid in helping to protect them from corrosion. This is a cost-effective and easy solution that you can find in the majority of homes. It's worth a shot before replacing hinges.

Doors that won't close

In time, doors become misaligned due to the expansion and contraction of wooden frames. This can cause the door catch on the corners or even latch when you close it. This issue can be resolved with a little effort. If you can tighten the hinges and fix the misalignment of the door, it will probably close again.

Begin by looking over the hinges to find any loose screws. Screws that are loose can cause a hinge to become sagging and create an opening between the leaf of the hinge and the jamb. This can cause the latch to be unable to pass through the strike plate's hole and cause a jammed door.

To fix this issue, remove one of the hinge screws and slide a strip of cardboard (we like to use the backs of old legal pads) between the hinge and the door jamb. Install the hinge. This will increase the gap on the side of the latch and reduce it on the hinge side. The latch can now clear the strike plate. If this fixes the problem, repeat the procedure on the remaining hinges.

If you still have problems, you can hammer or shim your strike plate to align it with the hole in the latch. If this is the case you're in, a small amount wood filler or paint is usually enough to hide the changes.


Long-term use and physical damage can cause the strike plate to become curled or warped, which can cause the latch to strike the edge of the hole but not extend into it far enough to ensure that the door is closed. Apply lipstick to the latch, and then adhere an edging strip on the strike plate. Close the door and open it. The lipstick will leave a mark on the tape where the latch meets the strike plate hole. If the mark is lower than the hole, this indicates that your latch should be moved up.