The Ugly Facts About Fiat Panda Key Fob Replacement
Reasons Your Fiat 500 Key Fob Won't Work
A fiat 500 key fob is a handy way to unlock the doors and get started the car. There are a variety of reasons why the fob won't work. It could be due to a dead battery damage to the receiver module, problems, and interference.
This listing is for an NEW replacement Fiat Flip Key Remote that is similar to the Ilco brand. It has to be professionally programmed (click here to search for local locksmiths for automotive locksmiths). It includes lock, unlock, and trunk buttons.
fiat key fob replacement fob doesn't work is a dead battery. Modern key fobs operate with a restricted operating range, and should be within just a few feet of the vehicle in order to function. If you're far from your vehicle when you press the key fob button the car won't be able to respond, and will display a "Key Fob Not Detected" message in the instrument cluster.
If this happens, simply replace the battery in the coin cell (Part number CR2032) with a new one from a reputable brand like Panasonic, Duracell, or Energizer. You can typically find them in your local hardware store or online.
After you've replaced the coin cell battery You can test it by standing close to your Fiat 500 and pressing the buttons. The car should blink its parking lights and the key fob should operate the lock and unlock switches.
If the key fob doesn't function after replacing the battery, it may have water damage that stops it from communicating with the receiver module in your car. Water damage can occur in a variety of ways, such as a simple splash or submerging the key fob into saltwater at the beach. If you suspect your fob was exposed to water, you can try placing it in a dry rice bag to draw the moisture back out. If this doesn't work, you will have to get your fob replaced by an auto locksmith or a dealer.
Water Damage
The fob does have rubber seals to keep water from the electronic chip inside the device, submerging it into the ocean or washing it in a machine can cause water damage. Saltwater poses a particular risk to the circuit board of the fob, causing it to short out and eventually end up dying. It's not good to let the fob get wet, but don't give it up in the event that you accidentally drop it in the water or don't remove it from your pocket.
First, remove the battery. Before replacing the battery, clean the electronic chip with isopropyl or similar products. Test the fob afterward to see if it is functioning. If the key isn't working, it may have to be reprogrammed. This is usually done by an auto locksmith or dealer.
If the key is older and has not been programmed to your car It will most likely need to be replaced completely. A professional locksmith for cars will be able to complete this process. The locksmith will need the key to be cut to match your car's ignition. The locksmith also needs to program your fob into the car's system. This is a cheap and quick procedure that can be completed in the same day.
Receiver Module Issues
One of the most common reasons why your 500 key fob could stop functioning is because it's out of range. The remote's range is of 30 feet, which means in the event that you are far from your vehicle it won't be able to respond to your commands. It's easy to fix this by moving the remote closer to your vehicle until it responds.
If you've replaced the coin battery (commonly known as"button" or "button" or "watch") and your fob doesn't function, it could have an internal circuit board problem. In most cases, reprogramming the fob will fix the problem. You can find instructions on how to do this for all automobiles by searching YouTube or checking out the owner's manual.
It is possible to replace the metal clips that hold the coin batteries in their place. If they become loose, it could prevent your coin battery from being properly seated, causing your remote to malfunction.
In rare cases the fob might become desync'd with your vehicle due to software problems or hardware issues. You can fix this problem by visiting your local auto-locksmith or dealer to reprogram your key fob. In certain instances they may have to install the software again in your body control module too.
Interference
Interference can also cause the key fob to not be able to receive or transmit a signal. This could occur if the keyfob is located in close proximity to a radio transmitter like a cellphone or radar detector. The key fob could not work due to a poor connection with the buttons or water damage, or damage to the internal chips.
If the key fob has failed to work one day out of the blue, or after trying everything you can at home to solve it e.g. You may have a faulty 500 receiver module If you've tried replacing it with a battery, reprogramming or using an alternative key fob. The receiver module, which is located under the dashboard, receives radio frequency signals from your key fob. It then converts them into electronic commands that the vehicle interprets.
Luckily, there is an easy method of resetting all of the on-board systems in your 500, including the key fob. Disconnect the battery for 15 minutes by taking off first the negative cable and then the positive cable. Reconnect the battery. This will get rid of any remaining electrical charge and restart the car's computers. This could allow you to get your key fob working again. If the problem persists it is recommended that you consult an expert technician. They will be able to identify the exact cause of any issues.
