10 Quick Tips About Subaru Keys How to Get a Subaru Replacement Key

If you've have lost your Subaru keys or require a new set, there are plenty of methods to obtain one. This article will provide few of the most popular ways.

Find the transmitter circuit board in your key fob. Your owner's guide should have instructions on how to open it. Note the first 8-digit number on the chip.

Keyless Entry

Keyless entry allows you to unlock and start your car without a mechanical car key. subaru impreza key , sometimes referred to as Toyota Smart Entry by some manufacturers, works by using an electronic signal that travels between your key fob and your car. The car responds by releasing or starting the engine. Certain keyless entry systems permit you to open your trunk.

The electronics in key fobs, in contrast to traditional keys that are easily damaged, bent, or scratched, are designed to resist damage. They aren't foolproof. They can be hacked and pose security risks. This is why you should change the codes on your key fobs regularly and avoid leaving them in reach of others.

In order to activate the keyless system, you need to put your hand on the door handle (or press a button on the handle of the door itself). Your vehicle then sends out an incredibly short radio signal, which will only work within a close range. If your key fob is within this distance, the car will respond with an unlocking code or restarts the vehicle.

It's essential to get a professional installed your keyless entry system. Some aftermarket kits only unlock driver's doors, while the most advanced ones offer remote start and smartphone connectivity. An expert installation can ensure that the installation is done properly and will not cause any problems with your vehicle's wiring.

Ignition Switch/Lock Cylinder

The ignition switch is an important mechanical device that locks the engine of the vehicle when the key is not in position. This helps prevent car theft. It may eventually wear down, causing it to jam or become stuck when the key is either inserted or removed, or hinder starting the vehicle. A locksmith is usually able to fix this issue by replacing or smoothing the wafers.

The lock the cylinder is a more complex part that can also wear out over time and make it difficult to insert or remove the key from the ignition. Locksmiths are usually able to smooth the wafers inside the cylinder, but it may also be necessary to replace the entire cylinder.

In the majority of instances, a skilled locksmith can bring your Subaru back up and running in a matter of minutes. They can even design a spare key so you're ready when the original one is worn out.

You can also buy a replacement key from a dealer, such as Hiley Subaru of Fort Worth, if you prefer. The dealer will make sure that the key has been properly programmed and is appropriate for your model. You could also receive the benefit of a warranty or other advantages from the dealer that don't get from an aftermarket company. The dealer can also make you a standard key if your Subaru does not have an transponder chip and isn't an older model.

Key Fob Battery

If your key fob doesn't work as well as it did to unlock the doors or start the car it could require an upgrade to the battery. This is especially true if you notice that the signal strength of the key fob is gradually decreasing and you'll need to click the button a lot harder or more than before in order to get it working.

The process of replacing the battery is relatively simple. First, you'll need to open the keyfob. This is done using an a flathead screwdriver that is placed in various places around the edges.


Then, insert an flathead screwdriver or coin into the slot or notch which separates the key fob's two halves. Then, remove the old battery, then place a new one into the same place and ensure that you use one that has the same chemical composition as the older one (CR2016 batteries are the most common). Finally you can snap the fob's two halves back together.

The majority of key fobs utilize CR2025 lithium button/coin cells that are sold in packs of two or six at many general stores and home improvement stores. You can also find them on the internet, and they are typically sold by well-known brands like Energizer and Panasonic.

Key Blanks

You'll be able to see that they're all identical if you take a closer look. But, it's important to keep in mind that the vast majority are nickel silver and are made to last longer than keys that are made of brass. This prevents key breakage, which saves money on service calls, maintenance and replacement keys. Kaba Ilco Corporation produces our blanks. They also make "LookAlikes" which function like brand-name locks when properly cut.

Our parts department stocks all the replacement parts and key blanks you need for your Subaru. We also carry high-security keys with additional security features such as a laser-cut design which makes them more difficult to duplicate, and an immobilizer that disables the engine if your vehicle has been altered with.

We suggest that you work with an Subaru dealer or retailer authorized by Subaru like Hiley Subaru of Fort Worth. The technicians will confirm that you are who they say you are and confirm that your Subaru model is accurate and will also check the warranty status. They will also ensure that the unique transmitter number has been reprogrammed correctly if you require a new transponder keys. They generally charge between $50 to $250 for this service, however you may be able to get a portion of the cost covered by your car warranty or roadside assistance plan.