What's The Reason Everyone Is Talking About Kia Picanto Key Fob Replacement Right Now How to Replace a Kia Sportage Replacement Key

The key on many Kia models has an electronic keyless entry system built into. The key is usually akin to the remote control and is able to be replaced with a new one from a Kia dealer or locksmith.

Key fobs might stop working due to a number of reasons, including the battery being dead, worn-out buttons, signal interference or water damage. Here are some tips on how you can get your Kia Sportage replacement key to function again.

How to replace the remote key or the smart key?

If your Kia is equipped with an intelligent key, remote key, push to start key or a regular non-transponder steel key the battery in these keys will eventually require replacing. This is especially relevant if your car displays a message telling that the remote or smart key has low battery power.

Fortunately, it's an easy procedure. To replace the keyfob battery take out your mechanical key from the slot at the back of the fob. Then, pull the cover off. Inside the key fob, there will be an incredibly small screw that holds the battery in place. Take out the old battery by detaching the screw using a small screwdriver. Install the new battery and then close the cut on the key fob.

Test the key fob by pressing the lock and unlock buttons. You're good to go in case the doors lock and unlock as you expect. You can now take advantage of the Kia's hands-free lock/unlock feature when your fingers are cold or you have to run some errands in Brandon.

Not all keys may require to be programmed (transponder chips or smart keys). This requires a machine for programming that is available only to the locksmith for cars or dealer. Other keys (non-transponder metal keys) don't require programming. If kia key programming need to be reprogrammed, you will need to be aware of the key code number stamped on the tag of the key code and keep the number in a secure place.

How do you replace a dead battery?

If the Kia key fob doesn't respond when you press the lock/unlock button, it's likely that the battery is depleted. A battery that is not functioning properly can cause other issues, like the check engine light flashing or the engine not turning correctly. Fortunately, replacing the battery on the key fob is a fairly simple DIY project that requires only a few basic tools.

Be sure to turn off your vehicle and close all doors before you begin. Find the small metal or plastic piece at the bottom of your key fob, and move it until a metal key slips out. The key can be put into the door's driver handle to unlock your car.

To replace the key fob's battery, take off the cover at the rear and use a pry bar tool to remove the latch holding the black negative battery cable. Remove the old battery, and then align the new one so that the "+" positive side is facing you and the "-" negative side is facing towards the fob's electrical contacts made of metal. Push the new CR2032 battery straight into place without putting too much force on it to avoid damaging or bending the metal contacts.

Once the new battery has been installed, turn the key fob off and back on in the ignition several times until the door locks cycle. You can then test your Kia's keys fob once more to ensure it's working as intended.

How can you replace the smart key


There is a possibility of having a standard keyfob or a Smart Key depending on the model of Kia Sportage. The difference between the two is that the smart key has the small blade of a key in it, whereas the standard fob doesn't. Both key fobs are equipped with an internal battery that will eventually require replacement. It's quite simple and takes just two minutes.

Be sure to switch off your Kia and sit on a flat or well-lit surface prior to when you begin. Also, remember that there are tiny components inside the fob that can be snagged if not cautious.

The first step is to find the small release button that is located on the back of the lower part of the fob. It's either an oval or circular slot. You can open the key fob by pressing the button.

After the key fob has been open, remove the battery. The new battery is a CR-2032 that can be purchased online or at your local auto parts store. Once you're done, your key fob will allow you to lock and unlock your vehicle even if it's not running.

How do you replace a broken mechanical key

The Kia key fob is a great convenience that allows us to lock and unlock our vehicle with the push of an button. As with all devices, the Kia key fob can occasionally have problems. There are solutions to fix these problems and keep your key fobs working for a long time.

A dead or drained battery is one of the most frequently encountered issues. This could cause your device to stop working or work intermittently. If this is the problem, replace the battery with a new one.

If this doesn't solve the issue Try using a standard flathead screwdriver to wedge open the casing of the fob's plastic. Be careful not to scratch any internal components or scratch the plastic. When the battery is open, carefully take off the battery that was removed and replace it with a brand new one.

After the new battery has been put in, shut and open the doors using the mechanical key (every key fob in the kia has an emergency mechanical key that can fit in the slot). Test the key fob to ensure that it's working correctly. If the fob still isn't working, call an expert locksmith or dealer to help resolve the issue. To avoid lockouts in the future, ensure you purchase an emergency key that will work on all door and trunk cylinders.