Five People You Should Know In The Repair Car Keys Industry How to Repair Car Keys

The car keys are small and may not seem important, but they're vital for the operation of your vehicle. The cost of replacing an old or modern transponder car key can range from $200 to upwards of $200.

However, there are ways to repair your car keys at home with less than. This article will go over some of the most common car key problems and the DIY solutions.

Dead Key Fob Batteries

The remote key fobs that are included with cars make it simpler than ever before to open the trunk, doors and tailgate. The battery in this device is susceptible to dying. Fortunately, there are some techniques that can be employed to solve this problem in a pinch.

Check to see if your vehicle is still in ignition mode. If it is, the battery on the key fob could be drained instead of dead. To test this, press the button on the fob against the ignition button on the vehicle. If this works, then the battery is likely fine and will only need to be replaced.

To replace the battery in the fob, open the case with a screwdriver. Be careful not to press too hard because this could cause the fob to split apart. If the fob doesn't seem to be coming easily, try putting your pry tool into several places around the outside of the case.

Once the fob is open, remove the mechanical key and open the electronic section of the car. Install the new battery and snap it back into the shell. If the key fob isn't working after this procedure, there could be a larger problem with the remote start system that requires a professional to diagnose. A reputable mechanic will be capable of helping you if this is the situation. You can also reach out to roadside assistance for help with your vehicle if needed.

Broken Key Ring

If your key fob isn't working because the ring broke there are a few options you could try. Check to see if you can locate the broken part within the ignition. If it's still in there the ignition, take it out without damaging the ignition lock or the door lock. If you're having difficulty removing it, call an expert locksmith. They have special tools that are able to safely remove keys that are damaged from the ignition.

A broken car key could be caused by corrosion of the plastic frame or circuit board. You can clean the board with rubbing alcohol and a cotton swab. This will remove the corrosion and prevent damage to the contact pads.

how to repair car key fob can fix a broken ring by using a thick wire or nail to close the hole. Superglue can also be used to repair a damaged ring. First, clean the broken ring with a damp cloth and then apply a small amount of superglue on each end of the nail or wire. Allow the pieces to dry, and then press them in place. These DIY solutions might seem appealing, however they are only temporary solutions. For long-term repairs, it's recommended to get a professional locksmith. They have the knowledge and tools to fix the broken key quickly and efficiently. They can even replace the battery in your key fob, and change it's programming if required.

Broken Key Blade

Some key blades break due to a lot of wear and tear. If this happens, it's time to get a new key. This problem isn't nearly as serious as you might believe at first. The most significant issue is that the blade broke off from the case.

One way to fix this is to spray the key hole with fluid that lubricates the key hole. You can then employ pliers or tweezers grasp the broken end of the key and pull it. If remote car key repair near me is magnetic, you can also use a magnet to pull it out. Be careful not to use a magnet on an ignition key as it could cause the lock tumbler to break.

Contact a locksmith right away when you are unable take out the damaged part of the key. They're equipped with special tools that let them safely remove keys without causing further damage.

Super glue can be used to fix an open lock that has snapped. Apply a small amount to the edges and press them together. Then, wait until the glue dries before inserting your key into the lock. However, this method isn't reliable and you may have to repeat the process a few times before it is successful. In addition the super glue may not be enough strong to hold the key together. This is more of a temporary solution than an option that is permanent.

Broken Plastic Loop

If the plastic loop on your key fob is damaged it can make the key useless. It's an easy fix. For a replacement alternative, you can opt for a thick wire or finishing nail. Drill two holes in the damaged loop of plastic for each end of the nail or wire. Cut the wire or nail into a key width, and place a small drop of superglue into each hole. Press the nail or wire into the holes and allow them to dry.

A locksmith who sells replacement shells is a different option. They can transfer the programmable part of your key to the new shell and cut new blades for less than the cost.

This isn't the best solution, but it will get you on the road again if your key broken in half. It's not easy to repair if the key blade is in the ignition however. You can try using hair clips, a needle or an extractor tool to pull the broken part of the ignition, but this can be risky if not cautious. The best option is to contact a locksmith with special tools for safely removing broken keys from the ignition. You can also have an entirely new key made using the correct cuts to fit the ignition of your vehicle.

Broken Master Key


You'll have to attempt to retrieve the key before it is completely destroyed. There are a variety of methods you can use, including using lubricants and tools like needle nose pliers or tweezers to grab a fragment of the broken key and pull it out.

To start, spray the inside of your lock with a lubricant like graphite powder or WD-40. You can also employ the hacksaw blade method, which involves moving the blade along the sides of the broken key, and then grasping a few of its teeth. If you're successful you will be able to take the broken key out.

Another tool that is useful is a spiral key extractor, which you can find in a variety of hardware stores. This tool has a thin rod that is flexible and has spiral threads that can be placed in the keyway, and later bent to form the broken part of the key. Once it has been snagged onto the serrations, it is possible to twist it in a circular direction and lever it against the broken portion of the key to take it out.

It's worth trying to get rid of the master key that is broken before calling an expert locksmith. If you are unable to get a piece out, you need to call the big guns - get a locksmith to cut you a brand new key and reprogram it with the transponder of your car.