5 Common Myths About Repair Car Keys You Should Avoid How to Repair Car Keys

The car keys are tiny and might not seem to be important, but they're essential for the proper operation of your vehicle. The cost of replacing the traditional or contemporary transponder car key can range from $200 to upwards of $200.

There are solutions to fix your car keys yourself at a fraction of the price. This article will address the most common car keys issues and their DIY fixes.

Dead Key Fob Battery

The remote key fobs for keys that come with cars make it simpler than ever to open the trunk, doors and the tailgate. The battery in the device is prone to dying. There are a few tricks you can use to resolve this issue fast.


First, determine if the car is in ignition mode. If it is, then the battery of the key fob may simply be depleted instead of dead. To test, press the button on the fob against the ignition button of the vehicle. If it works, the battery is probably in good condition and will only need to be replaced.

To replace the battery within the fob, open the case with an screwdriver. Be careful not to press too hard as this could cause the fob to break in two. If the fob won't open Try using your pry tool more than once around the outside of the case.

Open the electronic part of your vehicle after you have removed the mechanical key. Then insert the replacement battery and then snap the shell back together. If the key fob doesn't work after this procedure, it could be that there is a larger problem with the remote starting system in your car. This requires an expert to identify. If this is the case, a reputable mechanic should be able to help you. You can also reach out to roadside assistance for assistance with your vehicle if needed.

Broken Key Ring

There are a few things you can do when your key fob does not work because the ring has been broken. Check to see if you can locate the broken part in the ignition. If it is, remove it without damaging the lock on the ignition or door lock. Contact a locksmith if are having trouble removing the key. They have specialized tools that are able to safely remove a damaged key from the ignition.

key repair near me for a broken car key is the corrosion of the circuit board or plastic frame. You can clean the circuit board by using a cotton swab soaked in ruby alcohol. This will eliminate the corrosion and prevent damage to the contact pads.

If your key won't start because the ring broke, you may be able to fix it by using a thick wire or nail to seal the hole. Superglue can also be used to fix a broken ring. First, clean the damaged rings with a damp cloth and then apply a small amount of superglue to each end of the nail or wire. Allow the pieces to dry, and then press them in place. These DIY solutions may sound appealing, however they are only a temporary solution. It is recommended to hire an skilled locksmith for any long-term repairs. They have the tools and know-how to fix a broken car key quickly and efficiently. They can even replace the battery inside the key fob and reprogram it if needed.

Broken Key Blade

Some key blades break due to a lot of wear and tear. If this occurs, you must purchase a new one. Luckily, this problem isn't as bad as it appears at first. The primary issue is that the blade snapped off the case.

Spraying key repair near me into the keyhole is a method to fix it. You can then make use of pliers or tweezers grasp the damaged end of the key and pull it. If the key is magnetic, you could also use a magnet to pull it out. Use a magnet to help you remove the key, but be cautious to not sever the tumbler of the lock.

Call a locksmith immediately in the event that you are unable to remove the broken piece of the key. They're equipped with special tools that let them safely remove keys without causing further damage.

You can also use super glue to repair a snapped key. Apply a small amount of glue to the edges and press them together. Wait until the glue has dried before inserting the key into the lock. This method isn't very reliable, and you might have to repeat it several times before it does the trick. Plus the super glue might not be enough strong to keep the key in place. So, this is more of a temporary measure rather than a permanent solution.

Broken Plastic Loop

If your key fob's plastic loop breaks off it can render the key useless. Fortunately, this is an simple fix. For a replacement alternative, you can opt for a thick wire or finishing nail. For each end of the wire or nail, drill two holes into the plastic loop. Cut the wire or nail to key width, and place a small drop of superglue into each hole. Apply the nail or wire into the holes and let them dry.

Another option is to purchase a replacement shell from a locksmith who sells them. They can remove the programmable portion of your key, move it to the new shell, and cut the new blade for less than the full replacement cost.

It's not the best solution, but it will bring you back on the road in case your key broke in half. However, it can be difficult to repair the key blade if it's in the ignition. If you're not careful you can employ a hair clip, or a needle to take the broken piece from the ignition. The best solution is to contact a locksmith who has special tools for safely removing damaged keys from the ignition. You can also get a new key made with appropriate cuts to fit the ignition of your vehicle.

Broken Master Key

If a key is broken inside the lock, you'll have to try to retrieve it before it is completely destroyed. You can employ lubricants, tweezers, and needle nose pliers to grab the broken fragment of a key.

Spray the inside of your lock with WD-40 or graphite powder. You may also try the hacksaw blade method that involves carefully moving the blade down the side of the broken key and attaching it to the 'teeth'. If you succeed in doing this you should be able remove the broken key from the lock.

Another tool that is useful is an extractor for keys spiral, that can be found in a wide range of hardware stores. It is a thin rod with spiral threads that can be placed in the keyway, and later bent to the broken portion of the key. Once it has caught onto the serrations, you can turn the bar in a circle and pull it against the broken part of the key.

It's worth trying to get rid of a master key that's broken prior to calling an expert locksmith. If you are unable to get rid of the broken piece then you'll have to call in the professionals. Locksmiths can create you a new key that will be programmed with the transponder of your car.