How To Research Peugeot Keys Online Peugeot 208 Key Replacement

Peugeot 208 key replacement is best left to auto locksmiths with experience who have the proper equipment and know-how. They will be able to create and program new keys much quicker than a dealership and at a cheaper cost.

A dead battery for your coin is most likely to blame when your key fob stops locking or unlocking doors. There are other reasons for the key to be malfunctioning.

Dead Coin Battery

A dead coin battery will stop your Peugeot 208 from locking and unlocking, and also making it impossible to start the engine. If this is the scenario, you'll need apply the backup starting technique that is described in the owner's manual to your vehicle.

Another reason why the 208 won't start is that the spark plugs are been worn down. The spark plugs light the fuel to start the engine. However, they have a limited life span. They will eventually break down in the event that they aren't utilized enough.

There is a straightforward solution to this issue. The best option is to check the voltage of your car battery with a multimeter. If the voltage falls below 11,5 volts, it's the time to replace it. If the battery has corrosion it is necessary to clean its contacts. This can be accomplished by removing the rubber cover from the two battery terminals and then using a wirebrush, you can remove any corroded parts of the battery. After that, you need to connect the positive pole cables to the negative.

Water Damage

If your 208 doesn't start and the battery is not flat, then you need to make sure that the spark plugs work. You may find that they are simply too dirty and do not spark. The spark plugs can be cleaned in the workshop.

Peugeot automobiles are equipped with a transponder that is compatible with the immobiliser. This ensures that only a valid key can turn the engine. If the chip inside the Peugeot key is damaged then it will not send the correct signal to the vehicle.


This is a very common issue that is caused by water damage. This is particularly common in colder climates, where the vehicle may have been exposed to rain or snow. In this case, contact an experienced locksmith who will have the necessary tools and equipment to modify the key. They will also have all the latest technology and equipment required to make a Peugeot smart key. The process should not take more than 15 minutes.

Faulty Battery Contacts

Peugeot replaced the transponder chips by introducing a new version that makes use of electronic components that are mounted on a circuit board. The new system works great when it's new, however the circuit boards degrade over time and stop working properly.

This could prevent the immobiliser chip from activating, so your car won't start. Contact a Peugeot specialist or a locksmith, if this is the case.

Another issue that is common is when the battery in the key fob is dying, this causes the key blade to stop getting into the lock. A locksmith from your car will replace the battery and then cut a fresh blade for you. This is a quick solution.

Faulty Receiver Module

It could be that the receiver module has a problem If your Peugeot key fob fails to function after being dropped on the floor, or exposed to a stormy rainstorm, or accidentally washed. The receiver is responsible for sending radio frequency signals to the on-board computer, which controls the central locking system in your Peugeot vehicle.

The key fob itself has rubber seals to prevent water from getting to the chip inside. However, prolonged exposure to water may cause damage to these seals and the chip. Submerging the key fob in the ocean at the beach or throwing it into the water can be particularly damaging due to the high salt content.

The module needs to be replaced if your Peugeot spare key isn't working anymore. This can only be done by a Peugeot specialist or an expert auto locksmith. Peugeot keys are, unlike other vehicles, are secured by an immobilizer device. replacement key for peugeot partner van G28 Car Keys requires the right code to begin the car. This is why you should go with a knowledgeable Peugeot locksmith to handle the task of programming and creating an alternative.

Computer malfunctioning on-board

The on-board computer of your Peugeot is responsible for a variety of systems in your car, including power windows and airbags. The on-board computer displays an error code when something goes wrong. This code is saved in the system and will remain there until the issue is resolved. Most often, this involves replacing the onboard computer.

The most typical reason for the warning light for airbags to illuminate is corrosion or loose connections in the sensor. This can occur due to wear and tear, aging or exposure to moisture and salt. This issue must be addressed as soon you can, as an airbag malfunctioning could pose a risk in the event in the event of an accident.

If your Peugeot is showing a card that is not being detected error, then the battery inside the key fob may be weak or dead. This prevents the key fob from sending a signal that disarms your vehicle's standard immobilizer. Test this by pressing the unlock key on the key fob and then trying to start your car. If this does not work the battery on the key has to be replaced.