10 Replacing Upvc Window Handles Tips All Experts Recommend Replacing uPVC Window Handles

Switching the handles of windows made of upvc is a simple task. It is crucial to make sure that the new handle is fitted into the spindle cutouts in the window mechanism.

If the steps listed below are followed correctly the cockspur handle will be able to fit into most windows. The key is the step size of the handle.

What to Look For

Over time, uPVC handles on many windows in the UK begin to show signs wear and wear and tear. If this occurs, the window handle can become loose or difficult to operate, which makes it necessary to replace it. This is a relatively simple job that can be completed by anyone who is familiar with basic hand tools.


The first step is to make sure that the handle is securely attached to the frame of the window in the open position. The next step is to locate the screws or pins that hold the handle. They are typically located on the inside of the handle. They can be removed using a screwdriver and pliers.

When the handle is loose and sagging, gently pull it back from its hinges. It is then necessary to locate a replacement handle with the same design and size. This can be done at an online store or in a DIY store. The procedure should take just five minutes, and you will need a screwdriver.

One important factor to consider when replacing a uPVC window handle is the step height. This is the distance between the handle's base and where it is placed in the window frame. It is generally a standard measurement, and it is essential that you examine the step height of your existing handle before ordering a new one.

Depending on the type of handle you are using There are various sizes available. Inline handles for uPVC windows typically feature lug centers of 31mm, and there are also handles with cockspur that have 43mm centres. Tilt and turn handles are commonly found on windows made of uPVC and they feature a specific design that allows windows to be slid up to allow for ventilation, and then turned to open the window completely.

The most common breakage in uPVC handles is that they crack internally instead of breaking away from the base section. This makes it difficult to open. It is important to ensure that the replacement handle has the same spindle as the original one.

Remove the Old Handle

A poorly installed or damaged window handles may cause your double-glazed windows to close or open improperly and could even cause them to become stuck. This could be due to many factors, such as general wear and tear on the handle or corrosion. In these situations it is crucial to replace the window handle as quickly as you can in order to prevent further damage or loss of functionality.

When replacing the handles of windows made of upvc it is recommended to remove the old handles from the window. Begin by removing the screw by the handle while it is in the closed position. After you have removed the screw, you are able to remove the handle. You can make the process easier by using an electric screwdriver.

You should also be aware that screws can be hidden beneath caps made of plastic. It is best to remove the covers using the help of a Stanley knife. After removing the handle, you'll have to examine the square cutout on the base to ensure that the new handle you choose for the window lock is compatible. It is crucial to measure the spindle length on the old handle and compare it to the dimensions of the window mechanism spindle cutout.

The different kinds of window handles made of upvc are: Espag handles, which feature a central screw that can be turned left or right; Cranked handles, with two screws, and are used on tilt and turn upvc windows and Spade handles with an arm that is flat and can be put on either side of the window. It is simple to replace the handle when you've identified one that is suitable. Just screw it into place, and make sure the spindle is inserted correctly in the lock mechanism. After you have done this you can tighten the handle onto the window frame. Your replacement upvc handles will now be secured.

Measure the Spindle

If you're replacing a upvc window handle that has come off, it is likely because the spindle holding it in place has become loose or damaged. In some cases this can be fixed using screws or pins to tighten it. In some cases it might be necessary to replace the handle. There are several different types of handles made of upvc. There are three kinds of handles: inline espagnolette tilt-and-turn, and cockspur. Each type of handle is installed and replaced in a different manner.

Before buying a replacement handle it is essential to know the size of the existing one. This will ensure that the new handle is the right size and will fit correctly into the window. Fortunately, all handles adhere to industry standards of sizing making it quite easy to locate the right size.

To measure the size of the handle you must turn the window to the open position. door handles Repair My Windows And Doors should be able to see the dimensions of the screw or pin that secures the handle. Then, use a tape measure or ruler to determine the length of the spindle. Once you have determined the length of the spindle you can purchase a replacement one that is the same length.

The step height of a upvc window handle is also a factor to take into consideration when buying replacements. The step height is the distance from the base of the handle until where it sits on the frame. This usually is approximately 21mm or 9mm in aluminum and uPVC. To make sure that the new handle will fit the gap, drop something in the gap to check how far it extends before meeting an obstruction.

Cockspur handles may have different backsets depending on what style of window you install them in. Inline Espag handles come with a standard height of 43mm centre to centre (2 fixing points). Cockspur handles have different backsets depending on the window they are placed in. This is because they have a spur that extends from the handle and locks onto a cockspur wedge striking plate.

Install the New Handle

Once you've selected the new handle, ensure that it is aligned with the screw holes on the door. Then, secure it with the screws provided. If you're replacing the latch lever it can be put in the same way as the main door handle. After that, attach the door trim in order to conceal the mounting screws and close the job.

Tips: To remove a metal head from a wooden wedge place the handle on the floor, so that its wide end is on the floor. Then, use an hammer and tap the narrow end. Be careful not to damage the handle or the spindle.