10 Top Mobile Apps For Upvc Replacement Door Handles UPVC Replacement Door Handles

Over time, the handles on your doors will wear out and need to be changed. When replacing them, it is important that the new handles conform to the dimensions of the previous handle.

The top screw position as well as the lever and keyhole dimensions are the three measurements you have to determine. Check the size guide for assistance with this.

Inline Lever/Lever

A lever or lever door handle is a contemporary handle that can be installed on doors that are new or replacement. This kind of handle is available in many styles and finishes. A variety of manufacturers provide this handle, including Avocet ERA, Fullex, Hoppe, Mila, Millenco & Yale.

Fab and Fix Windsor Inline Sprung Lever Door Handle

The uPVC/Composite door handles are made of sturdy materials and are suitable for multi point lock doors that require a strong design. The handles are inline, and they use the same screws and spindle to fix them. They can be easily mounted on a new or existing uPVC/Composite door.

The handle can be adjusted and angled to fit the needs of all users. The handle has been tested to 200,000 cycles. This helps to ensure the quality of the finish and performance of the handle over time. The lever that springs is adjustable to fit a wide range of locks. This is especially useful for doors with narrower frames, in which the cylinder is further back. A lever that is shorter can be used on doors with latches which can be operated with the thumb located on the inside.

upvc replacement door handles Pad

The lever pad upvc handle is distinct from the lever handles that are used on the majority of doors. These handle types can either work off one single spindle (inline) or independently from both sides using two inline or offset spindles (pad). They are commonly employed on UPVC doors with double glazing. They are available in a variety of finishes and variations.

The handles have been tested to a minimum of 200 000 cycles and are available in several finishes like White, Silver, Chrome & Gold. The finish is in line with BS EN 1670:2007 Grade 5 and is also resistant to corrosion, which gives the handle a high degree of durability and performance for its intended use.

All of the UPVC lever pad styles for handles come with the spindle and screws, allowing them to be fitted on a new or existing uPVC door. The backplate fixation centers of 211mm allow for a bigger handle, which is often beneficial when replacing an old or faulty multi-point door lock mechanism. These handle levers have a spring, which solves the issue of door handles that sag out of their horizontal position when they are not being used.

When choosing the replacement UPVC handle and spindle it is crucial to match the dimensions of the PZ of the multipoint lock as well as the uPVC door. This measurement is also called the "handle centre" or "cylinder centres which is a crucial aspect in ensuring that you have the correct handles.

When you have the right PZ size you will then need to ensure that the lever pads and push pads are in a suitable shape to fit the American with Disabilities Act (ADA) compliant handles that you need for your doors. They are typically round or square, with an internal lever and an external push pad.

The majority of UPVC lever pads we offer are sprung, which means that they will return to their horizontal position when they are not in use, rather than hanging out and potentially sticking in the frame. This keeps draughts out of the property. Also, the majority of the UPVC handle lever pad style handles are swivel which allows you to place them on either side of the door.

Euro Cylinder

Cylinder locks are usually found on uPVC doors, but can also be found on other types of door. The cylinder lock operates by a key which unlocks the cylinder's case. The case is then able to reveal pins that can be aligned to the pins in the lock, and permit them to turn the revolving camera, thereby opening the door. Euro cylinders are available with up to six pins. Doors that are internal and external require different levels of security.


The selection of a cylinder is vital. It's dependent on the use that your doors and handles receive. External doors, for instance are required to be fitted with cylinders with greater security, whereas doors inside can be secured using an ordinary cylinder. Certain cylinders are equipped with additional features that increase security, such as anti-drill or anti bump properties.

A euro cylinder needs to be properly measured to ensure it's the correct size for your door. The cylinder should be measured from the central fixing screw hole to the other end of the cylinder including the thumb turn if you have one. It is best to do this with the lock in place however in the event that this is not possible, you can take it off to measure. It is important to ensure that there is no cylinder that extends beyond the handle or escutcheon. This could make it susceptible to lock snapping attacks.

The design of most newer cylinders has anti-drilling and bump resistance features. They are designed to decrease attacks by forcing cylinders to rotate in a new direction. This can to deflect attacks and ensure your door is secure.

There are also cylinders that are constructed to withstand snapping. This is a growing method of attack on cylinders where the break line inside the lock is targeted with a special tool to snap off the front of the cylinder to allow the door to be opened. This is a lot faster and more straightforward than gaining access through multipoint locks. It also leaves no evidence of a burglary, which can hinder the insurance claim.

Spring Cassette

This spring cassette is located within the base plate of your door handle. It offers a spring-loaded solution to help return your multipoint lock handles back to their original position after using. These handles used to have no spring, and would slide when the locking mechanism was removed. This simple feature is among the best methods to correct this issue and is a great way to prevent your doors made of upvc from becoming stuck in the open or closed position, as these are not always easy to manually close by hand.

These spring cassettes were designed to be used with sprung multipoint locks. They are not compatible with handles that are not sprung and you'll have to cut a hole into your backplate for them to fit. (Please look at the image for a technical diagram). They are a replacement for broken or missing cassettes in the backplate of the door handle for various kinds of uPVC doors. They feature a square cut-out that can accommodate an 8mm spindle, and are sold as a set.

These spring cassettes are a great cost-effective solution to the issue of handles on your doors sagging. They are easy to fit and will increase the lifespan of your uPVC doors. For more information about our wide range of uPVC accessories and spares, you can get in contact with our team. We are always available to provide expert advice and to assist you.