What Is The Best Place To Research Replacing Upvc Window Handles Online Replacing uPVC Window Handles

Switching the handles of windows made of upvc is a simple task. The most important thing is to make sure that the replacement handle fits the spindle cut out in the window mechanism.

If you follow the steps below the handle of any cockspur will fit most windows. The key is the step in the height of the handle.

What to Do You Look For?

Many of the windows in the UK come with uPVC handles Over time, they can begin to show signs of wear and wear and tear. When this occurs, the handle could become shaky or difficult to operate, making it necessary to replace it. Anyone who is familiar using a basic hand tool can complete this relatively simple job.

The first step is to make sure the handle is firmly connected to the window frame, and is in an open position. The next step is to locate the screws or pins that secure the handle. These are typically located on the inside of the handle and are removed with a screwdriver, or pliers.

When the handle is loose and sagging, gently pull it back from its hinges. The next step is to find a replacement handle of the same style and size. This can be done online or in an area DIY store, and the process should only take five minutes using the help of a screwdriver.

When replacing the handle of a uPVC handle It is crucial to consider the step height. This is the distance between the handle's base and the place it is located in the window frame. This is usually an average measurement, but it is important to examine the step height of your current handle prior to ordering an entirely new one.

There are various sizes depending on the type of handle. Inline handles are offered for uPVC windows with centers of 31mm for lugs, while cockspur handles come with lug centres of 43mm. Tilt-and-turn handles are commonly found on uPVC windows. They have a special design that allows the window to be tilted for ventilation and then rotated to fully open the window.

The most frequent uPVC handle breakage is internal cracking instead of a break at the base. This can make them hard to open and therefore it is crucial to ensure that the replacement handle you buy has the same length of spindle as the one you have.

Remove the old handle

If the handles on your windows are damaged or incorrectly fitted, they can cause double-glazed windows to close and open incorrectly. They could even become stuck. There are a myriad of reasons, such as general wear and tear or corrosion of the handle made of metal. In these instances it is crucial to locate replacement upvc window handles as soon as you can in order to prevent further damage and loss of functionality.

One of the first things to do when replacing window handles made of upvc is to remove the old handle from the window. Start by removing the screw by the handle while it is in the closed position. This will reveal a screw, and once it is removed, you are able to begin to remove the handle itself. You can make the process easier by using an electronic screwdriver.

Be aware that screws could be hidden under plastic caps. It is best to remove the covers using a Stanley knife. After the old handle has been removed, you must examine the square cut out on the base of the handle to make sure that the new window lock handles will work with it. This is important because you'll need to measure the length of the spindle of the old handle to ensure it matches the size of the window mechanism and the handle spindle cut out.

There are three kinds of upvc handles: Espag handles with a central screw that can be turned left or right and Cranked handles with two screws and Spade handles that have arms that are flat and can be used either side of the windows made of upvc. When you have a suitable replacement, it is just a matter of screwing the handle in place and making sure that the spindle is placed into the lock mechanism. After that, it should be tightened to the window frame and the replacement window handles made of upvc must be secure.

Take a measurement of the Spindle

If you're replacing a upvc window handle that has come off, it's likely due to the spindle that holds it in place has become damaged or loose. In some cases it is possible to tighten the spindle by using pins or screws. In some cases it might be necessary to replace the handle. There are many kinds of window handles made of upvc. There are three types of handles: inline espagnolette, tilt-and-turn, and cockspur. Each handle type is installed and replaced in a different way.

Before purchasing a replacement handle it is essential to know the dimensions of the handle that is currently in use. This will ensure that the handle will fit the window correctly and will be the right size. Fortunately, all handles adhere to industry standards of sizing making it quite easy to locate the right size.

To measure the handle's size, turn the window to the open position. Then, you should be able to determine the size of the screw or pin that holds it. Then you can use a ruler or tape measure to determine the length of the spindle. Once you have the length of your spindle, it is possible to purchase a replacement that is exactly the same length.

The step height of a upvc window handle is also important to take into consideration when purchasing replacements. repairmywindowsanddoors is measured from the base to the point at which the handle is positioned on the frame. This is usually around 21mm or 9mm in aluminum and uPVC. Dropping objects into the space will allow you to see how far the handle extends before it reaches an obstruction.

Cockspur handles usually have different backset heights, based on the type of window they are installed in. Inline espag handles have the standard height of 43mm from centre to centre (2 fixing points). Cockspur handles, however they have different backsets dependent on the design of the window they are in. This is because they feature a spur that extends from the handle and locks over a cockspur wedge striker.

Install the New Handle


Once you've selected the new handle, make sure it is aligned with the holes for screws on the door. Then, secure it with the screws supplied. Install the latch lever in the same manner as the handle that you are replacing if you are also replacing the door handle. After that, attach the door trim again to hide the mounting screws.

Tip: To remove the head of the metal from the wedge made of wood, hold the handle so its wider end is resting on the floor. Use a hammer to tap the thin end of the handle. Be careful not to damage the handle or the spindle.