15 Gifts For The Repair Car Keys Lover In Your Life How to Repair Car Keys

Car keys may seem tiny and insignificant, however they are vital to the functioning of your vehicle. The cost of replacing the traditional or modern transponder car key could be as high as $200.

However, there are ways to repair your car keys at home for a fraction of the cost. This article will cover the most frequently encountered car keys issues and their DIY fixes.

Dead Key Fob Battery

The remote key fobs that are included with cars make it easier than ever before to open the trunk, doors and tailgate. The battery in the device is prone to dying. However, there are some tricks you can employ to resolve this issue in a pinch.

First, check if the car is in ignition mode. If it is, then the battery on the key fob could be drained instead of dead. To test car key fob repair near me , push the button on the key fob right towards the ignition button. If this works, then the battery is probably fine and only needs to be replaced.

To replace the fob's battery, first pry the case off using an instrument like a screwdriver, or watch-type tool. Be careful not to apply too much force since this could cause the fob's case to split. If the fob isn't opening open with ease, try placing your pry tool in more than one place around the outside of the case.

After the fob has been opened, remove the mechanical key and open the electronic part of the car. Install the new battery and then snap back the shell. If the key fob isn't working after this procedure, there could be a bigger problem with your car's remote start system that requires a professional to diagnose. A trusted mechanic will be in a position to assist you if this is the situation. If you require assistance with your vehicle, you can contact roadside assistance.

Broken Key Ring

If your key fob won't work because the ring broke there are a few options you could try. The first step is to see if the damaged piece is still inside the ignition. If it is, you should remove it without damaging the door lock or ignition lock. Call a locksmith if you are having difficulty taking the key off. They have tools that can safely remove a damaged or broken key from the ignition.

Another common cause of broken car keys is the corrosion of the circuit board or frame. You can clean the board with the help of rubbing alcohol and a cotton swab. This will eliminate corrosion and ensure that the contact pads don't get damaged.

If your key won't start because the ring is broken or was damaged, you might be able fix it using a sturdy wire or nail to seal the hole. You can also use superglue to repair a damaged ring. First, clean the broken ring with a damp cloth and then apply a small amount superglue to each end of the wire or nail. Apply the glue to the ring and let them dry before using your car. These DIY solutions can seem appealing, but they're only an interim measure. For long-term repairs, it's best to get a professional locksmith. They have the tools and knowledge to repair a damaged car key quickly and effectively. They can even replace the battery in the key fob and reprogram it if needed.

Broken Key Blade

Some key blades break from a lot of wear and tear. If this happens, it's probably time to get a new key. The issue isn't as serious as you might believe at first. The main problem is that the blade has separated from the case.

One method to fix this is spraying the key hole with a oil-based lubricant. Then you can use pliers, tweezers, or a pin to grab the broken end of the key and remove it. If the key is magnetic, you can also try using a magnetic tool to assist in pulling it out. Just be careful not to use a magnet on an ignition key since it could cause the tumbler in the lock to break.

If you're not able to remove the broken piece of key, call an emergency locksmith. They're equipped with special tools to safely extract keys without causing further damage.

Super glue can be used to fix the snapped lock. Apply a small amount of the glue to the edges and press them in. Wait until the glue has dried before inserting the key into the lock. But this method isn't very secure and you may need to repeat the process a few times before it's successful. Super glue may not be able to hold the key in place. This is more of a temporary solution than a permanent one.


Broken Plastic Loop

If the plastic loop on your key fob is damaged it can cause the key to become useless. This is a relatively easy fix. As a replacement, you can use an extremely thick wire or a finishing nail. Drill two holes into the plastic loop that is broken at each end of the wire or nail. Cut the nail or wire to the desired width and then put the superglue drop in each hole. Press the wire or nail into the holes to seal them and allow it to dry.

Another option is to get the replacement shell from a locksmith that sells them. They can remove the programmable part of your key, transfer it to the new shell and cut the new blade for less than the full replacement cost.

This isn't the most efficient option, but it can get you on the road once more if your key split in half. However, it can be difficult to repair the key blade if it's in the ignition. You could try using a hair clip or needle extractor tool to remove the damaged part of the ignition, however it's risky if not careful. Call a locksmith with special tools to safely remove damaged keys from ignitions. They can also design new keys with the proper cuts for the ignition of your vehicle, so it will work correctly when inserted into the lock.

Broken Master Key

You'll have to attempt at regaining the key before it is completely destroyed. There are a few techniques you can use, including using lubricants as well as tools such as needle nose pliers or tweezers to take a small piece of the broken key and then remove it.

Spray the inside of your lock with WD-40 or graphite powder. You can also try the hacksaw blade method that involves moving the blade across the face of the broken key, and then grasping a few of its teeth. If you're successful then you should be able to remove the broken key.

Another helpful tool is a spiral key extractor, which you can find in a variety of hardware stores. This has a thin flexible bar with spiral threads, that can be inserted into the keyway and then bent to reach into the broken part of the key. Once it has been snagged onto the serrations, it is possible to twist it in a circular motion and lever it against the broken portion of the key to get it out.

Before contacting a locksmith try to get rid of the broken master key. If you are unable to get a piece out, you need to call the big guns and let a locksmith make you a brand new key and reprogram it with the transponder in your car.