This Is The Ultimate Guide To Double Glazing Door Lock Repairs
Double Glazing Door Lock Repairs
Has your uPVC window or door mechanism deteriorated? Perhaps the window or door handles don't meet up correctly or are difficult to use.
You'll lose energy if your double-glazed doors don't function properly. This also increases the chance of burglary. Owen the Locksmith can repair your door lock at reasonable costs.
Snapped Key
It can be quite frustrating when a key snaps inside the lock. This can also be a security risk, as it may make you vulnerable to an intruder if the door does not lock. Fortunately, there are quick fixes that you can try to resolve the issue and get your door operating properly once more.
First, remember to stay calm. If you panic and begin poking around wildly you may end up pushing the broken piece of the key deeper into the lock, which could make the situation worse.
Spray WD-40, or any other penetrating oil, into the lock. This will help the broken piece to emerge more easily. You can also employ a screwdriver in order to break up any stuck pieces that could be hindering the flow. If you happen to have a small piece of the key hanging out it, you can make use of a paperclip or other metal object that is thin to grab it and remove it. Both methods work, but you must be careful not to push the broken key further into the keyway.
Some paperclips have grooved edges, which can serve to extract hooks and Jigsaw blades also work for this function. If you don't have any of these then you can bend a hook with needle-nosed pliers. Additionally, you can use a pair of tweezers grab and remove the last bit of the broken keys.
If you cannot remove the broken key piece then you can use a lock deicer. This is usually available at all hardware stores. It works by freezing any water or ice that could be in the lock.
If none of these solutions work, it might be time to consult a locksmith. The experts at Fitlocks can quickly fix issues such as broken handles or broken keys with uPVC locks and door mechanisms. They can also alter the double glazing door mechanisms to ensure that they are simpler to operate. You can request a double-glazing repair online or contact us to discuss your requirements.
Broken Cylinder
A damaged cylinder could pose a serious security risk.
double glazing window repairs can easily repair the cylinder. To fix the cylinder locksmiths must tap it. They can do this with a hammer or other tools, but the most effective method is to make use of a long match or a piece of wire. Then, place the match's tip or wire close to the keyway. The locksmith can then strike the lock in order to break it. This is more secure than using a hammer that could cause damage to the lock.
The most frequent cause for cracks in the head of a cylinder is due to overheating. This can happen when the cylinder block and head are made from different metals, such as cast iron and aluminum. When the different metals heat up and cool down at different rates, it may cause localised hotspots that expand faster than the rest of the cylinder head, thus leading to cracks.
Corrosion is another possible cause of cracks in the cylinder. When the cylinder head and cylinder block are not properly maintained, it can result in corrosion or rust and cause them to expand at a a higher rate than they should. In time, this could also cause cracks.
If your uPVC door or window lock is brittle or requires lots of pressure to turn, it can be caused by many things. This issue could be caused by a faulty locking mechanism or misalignment or a worn-out handle.
It is a quick and cost-effective fix that a majority of double glazing owners can accomplish. A professional locksmith is able to solve this issue within an hour of arriving at your home. Based on your requirements they will be able to replace the locking mechanism, replace the window handles, and also change the gearboxes. A professional locksmith will always be able advise you on the most cost-effective options for your home. They can also suggest upgrades to high-security 3 Star euro cylinders TS007 that add an extra layer of protection against burglars. This is a small cost to pay for the peace of mind that comes from knowing that your uPVC doors are safe.
Broken Handle
Window handle locks are complex mechanisms that deteriorate with time and use, so it's not a surprise that they sometimes break. It isn't always easy to pinpoint the reason for a broken window handle lock and fix it correctly.
Fixing your broken handle, whether it's an internal latch or locking mechanism will increase the security of your uPVC door and prevent draughts. It could be costly to replace or repair your handle if it is not done correctly and can also harm the frame and lock of your door.
With the window in the open position, loosen the screw that holds the handle using a screwdriver. This should be located on the inside of the back plate, and is normally covered by an aesthetically pleasing cover for the screw reasons. Be careful not to lose any of the internal parts within the handle, such as the plates or levers that are on either side of the spindle. Ideally, keep them in the same order so you can replace them again if needed.
Next, turn the handle to make it 90 degrees towards the window frame. Then, loosen the screw on the back of the handle which holds it to the internal spindle with another screwdriver. Once the screw is free, you can take the handle off and take out the broken spindle. Replace it with a new one, making sure that it is the same length as the old one (you can usually find these on the internet or at hardware stores) and securely screw it in the correct position. Do not overtighten the screw because this could cause damage to the handle and window frame.
Ensure the new handle is correctly installed Close the window and test the handle. It is likely that it will operate smoothly and you'll be able unlock your window.
Make sure to check that your uPVC window is shut correctly when you're using the handle. If they're not, you could experience damp and draughts inside your home as and also affecting your home's energy efficiency. A local window company, like Core Sash Windows, will be in a position to adjust the hinges on your window frames to ensure they can shut properly.

Broken Spindle
It is usually the case that the spindle within the handle breaks, rather than the handle itself. This is most common in uPVC tilt-and-turn windows. These kinds of windows require a handle which operates a locking mechanism in the window frame. The handle is attached to a rod in the centre that in turn activates mushroom-like locking cams, these locks are inserted into the window frame. If the dead latch mechanism is not able to open after the handle is turned, it is most likely the spindle has been damaged. This can be a problem that is frustrating.
Luckily there are ways to fix this problem. A professional locksmith can quickly and effectively address this problem. A good locksmith will be able to disassemble the handle of the window by using a tool to remove the wheel portion where the spindle is located. This can be done without damage to the handle or window frame.
After removing the wheel the technician can examine the spindle and identify the reason for its break. This involves breaking the spindle into its individual parts and meticulously noting their general condition, as well as any particular areas of wear or damage. This process is typically carried out in a clean room by highly skilled technicians.
The next step is to clean the damaged spindle, this will remove any dirt or other debris that might be obstructing its normal functioning. The spindle may then be repaired or replaced. If it's being replaced, the technician could use the dowel that is similar in size to the original and drill mating holes in both pieces of the spindle. This will ensure that the spindle will fit perfectly with the handle.
If the damaged spindle cannot be repaired, it could require replacement completely. Home centers sell generic replacements however if your window design is unusual, you will have to speak with a cabinet maker or woodworker who can recreate the exact piece. Once the new spindle is installed, it can be attached to the handle by line up the screw holes in the handle with the frame's existing screws. Once the new handle is firmly seated you will be ready to operate your uPVC window.