The Expert Guide To Fiat Panda Key Fob Replacement Reasons Your Fiat 500 Key Fob Won't Work

A fiat 500 key fob is a handy way to unlock the doors and get started the car. However, there are numerous reasons why the key fob might stop working. This includes a dead battery or water damage, problems with receiver modules, as well as interference.

This listing is for an NEW replacement Fiat Flip Key Remote - an exact replica of the Ilco brand that needs to be professionally programmed by a local automotive locksmith (click here to search for a Locksmith Search). It includes trunk, lock and unlock buttons.

Dead Coin Battery

A dead battery is the main cause of your 500 key fob being inoperative. Modern key fobs have only a limited range of operation and must be within just a few inches of the vehicle in order to work. If you are far from your vehicle and hit the keyfob, it will not respond and display the message "Key Fob Not Detected".

If this happens If this happens, replace the battery in the coin-cell (Part Number CR2032) by a fresh one of a reputable brand such as Panasonic Duracell or Energizer. They can be found in your local hardware store, or online.

You can test the coin-cell battery by pressing the buttons while you are standing close to your Fiat 500. The car will blink its parking lights and the key fob will operate the lock and unlock switches.

If the fob's key doesn't work after replacing the battery, it could have water damage that stops it from connecting to the receiver module inside your car. Water damage can occur in a variety of ways, ranging from a light splash to submerging your fob in salt water at the beach. If you think your fob was exposed to water, place it in a bag of rice to draw out the moisture. If that doesn't work your fob may need to be reset by an experienced auto locksmith or the dealer.

Water Damage

While the fob comes with rubber seals to keep water out of the electronic chip inside and out of the ocean or washing it in a machine could cause water damage. Saltwater is especially dangerous to the circuit board of the fob, causing it to short out and eventually die. The fob getting wet is not an ideal choice, but if you drop it in an empty cup of water, or do not remember to remove it from your pants pocket before running the washing machine and you don't have a chance, don't give in.

First, remove the battery from the fob. Clean the electronic chip with isopropyl ethanol or a similar product and dry it thoroughly before replacing the battery. Next, test the fob to see if it works. If the fob doesn't work, it may have to be reprogrammed. This is usually handled by an auto locksmith or dealer.

If the key is a newer model and hasn't been programmed to your car It is likely that it needs to be replaced completely. sneak a peek at this website is a simple process that can be handled by a professional locksmith for automotive use. The locksmith will require the key to be cut to match the car's ignition. They'll also have to reprogram the fob in the car's system. This is a cost-effective and fast process that can be completed on the same day.

Receiver Module Issues

Your 500 key fob might stop working because it is out of range. The remote has a range of 30 feet, so in the event that you are far away from your vehicle, it won't respond to your commands. You can easily remedy this by moving your remote closer to your vehicle until it responds.

If your fob isn't working after you replace the coin battery, also called a "button", "watch" or "button" it could be a problem with the circuit board inside. In the majority of cases, reprogramming your fob will resolve this problem. You can find the instructions on how to do this for all automobiles by searching YouTube or checking out the owner's manual.

You may have to replace the metal clips that keep the coin battery. If they become loose, it can stop your coin battery from sitting properly, causing your remote to malfunction.

In rare cases the fob can become out of sync with your vehicle because of hardware or software problems. It is possible to fix this issue by visiting your local auto-locksmith or dealer to reprogram your key fob. In some cases the software may require reinstallation to your body control modules.

Interference

In addition to a dead coin battery the key fob could not be able to receive or transmit the signal due to interference. This could occur if the keyfob's location is in close proximity to a radio transmitter such as a cell phone or radar detector. The key fob may not function due to a poor connection with the buttons or water damage, or damage to the internal chips.

If the key fob has failed to work one day suddenly or after trying every option at home to fix it e.g. replacing the battery, reprogramming it and using the spare key fob, you could have a faulty receiver module on your 500. The receiver module, located beneath the dashboard, is able to pick up radio frequency signals from your key fob. It converts them to electronic commands that the vehicle interprets.


There's a quick and easy way to reset the 500's in-board system, including the keyfob. Disconnect the 12 volt battery for about 15 minutes, by disconnecting the negative cable first then the positive cable. Then, reconnect the battery. This will clear any residual electricity, and restart the car's computer. This could help you get your key fob to work again. If the issue continues, you should seek out an expert technician. They'll be able to determine the exact cause of your issue.