Five Things Everybody Gets Wrong Regarding Double Glazing Door Lock Repairs Double Glazing Door Lock Repairs

Are you experiencing issues with your uPVC window or door mechanism not working properly? Perhaps the window or door handles aren't able to connect properly or are difficult to use.

You'll be wasting energy when your double-glazed doors do not perform as they should. This increases the risk of burglary. Owen the Locksmith will be able to fix your door lock at reasonable costs.


Snapped Key

When a key snaps off in a lock, it could be incredibly difficult. It can also be a security issue, as it may make you vulnerable to burglars if your door is not locked. There are a couple of quick solutions you can use to resolve the issue and get your door working again.

Remember to remain calm. If you get scared and start doing a lot of fumbling around you may end up pushing the broken piece of the key even further into the lock, making the situation much worse.

Then spray WD-40 or another penetrating oil into the lock to make the broken piece to slide out more easily. You can also make use of a screwdriver to break up any pieces stuck that might be blocking the way. If you're lucky enough to have a small piece of the key that is visible and you want to remove it, make use of a paperclip or other metal object that is thin to grab it and remove it. Both methods work well, however, be careful not to push the damaged piece of the key further into the keyway.

Some paperclips have grooved edges that can be used as hook extractors. Jigsaw blades are also well for this. If you don't happen to have any of these items then you can bend a hook using needle-nosed pliers. Additionally, a pair of tweezers is a good way to grip and pull out the last bit of the broken key.

If you're unable to pull the broken piece of the key out, you can try using a lock de-icer. It is available in most hardware stores and is used to freeze any moisture present inside the lock.

If none of these strategies seem to be helping, it might be time to call a locksmith. Fitlocks experts can quickly fix problems with uPVC door mechanisms and locks that have snapped keys as well as broken handles. They can also alter the double glazing door mechanisms so that they are easier to operate. Get a double glazing repair via our website, or give us a phone call to discuss your requirements.

Broken Cylinder

A broken cylinder can pose an extremely risky security issue. It's a good thing that it's a simple repair for an expert locksmith to complete. A locksmith must tap the cylinder in order to repair it. They can do this using an hammer or another tools, but the most effective method is to use a long match or a piece of wire. Then, place the match's tip or wire near the keyway. After that, the locksmith will strike the lock and break it open. This is far better than using a hammer, which could harm the lock.

The most frequent cause for cracks in the cylinder head is overheating. This can happen when the cylinder block and cylinder head are made from different metals, such as cast iron and aluminium. Different metals can be heated and cool at different rates. This can cause localized hotspots to expand faster than the rest.

Another possible cause of cracks in the cylinder is corrosion. If the head and block of a cylinder are not maintained correctly they may rust or corrode, which can cause them to expand more than anticipated. In time, this could also lead to cracks.

If your uPVC window or door lock is stiff and requires a lot of pressure to turn, it could be due to a variety reasons. This issue could result from a defective locking mechanism or misalignment and also a worn out handle.

Fortunately it's a simple and inexpensive fix for most double glazing owners. A professional locksmith will usually solve this issue within an hour of arriving at your property. They can replace the locking mechanisms, or change the window handles, and also change the gearboxes based on the specific requirements of your home. A professional locksmith can always advise you on the most cost-effective options for your home. They can even recommend upgrades to high-security 3 Star Euro cylinders, TS007, that will add an extra layer of security against burglars. It's a small amount to pay for the peace-of-mind that comes from knowing your uPVC door is secure.

Broken Handle

It's not a surprise that window handle locks could break. They are equipped with complex mechanisms that wear out over time. If yours fails it may be difficult to identify the cause of the problem and make sure you fix it properly.

The issue could be in the internal locking mechanism or the latch, fixing your broken handle will increase your uPVC double glazing door's security and help you to stop the draughts. When you aren't doing it right, replacing or repairing the handle could be expensive and can harm the door's frame as well as lock, so it's worth taking some time to make sure you do it right.

Screwdriver: With the window open remove the screw that holds the handle. The screw should be located on the inside of the backplate, usually concealed by the cap of the screw for aesthetic reasons. Be sure to not lose any internal components within the handle, for example the plates or levers that are on either side of the spindle. It is best to keep them in the same order so that you can re-install them when needed.

Then, turn the handle so it's at 90 degrees to the window frame. Finally, loosen the screw at the back of the handle that fixes it to the internal spindle with a second screwdriver. Once this is loose, you should be able to pull the handle off and pull out the broken spindle. Replace it with a new one, ensuring it is the same length as the old one (you can typically find these on the internet or in hardware stores) and securely screw it into place. Do not overtighten the screw because this could damage the handle and the window frame.

Close the handle and try it. It is likely that it will operate smoothly and you'll be able to unlock your window.

Don't forget to double-check that your uPVC window is shut properly when you're using the handle. If they don't, you could experience draughts and damp in your home as and also affecting the energy efficiency of your home. Core Sash Windows is a local window company that can alter the hinges of your window frames to ensure they close correctly.

Broken Spindle

It is usually the case that the spindle in a handle breaks rather than the handle itself. double glazing repairs is most common in uPVC tilt-and-turn windows. These types of windows require a handle which acts as a locking mechanism within the window frame. The handle is connected to a central rod which triggers a set of cams that look like mushrooms, they lock into window frame keeps. If the dead latch mechanism does not open when the handle is turned, it is possible that the spindle is broken, this can be an extremely frustrating issue.

Fortunately, there are ways to rectify this issue. A good locksmith can quickly and effectively fix this problem. They can disassemble the window handle by using a tool to remove the wheel component of the mechanism that is where the spindle goes. This is done without damaging the handle or causing any other damage to the window frame.

After removing the wheel, the technician can examine the spindle and identify the reason for its break. This involves breaking down the spindle into its component parts and meticulously noting their general condition, as well as any specific areas of damage or excessive wear. This process is usually carried out by technicians in a clean and safe environment.

The next step is to clean the damaged spindle. This assists in removing any dirt or debris that might be obstructing its normal functioning. After this the spindle is cleaned, it could be repaired or replaced. If the technician is replacing the spindle he can use a dowel that is the same size to the original. He will then drill holes that are identical to both pieces. This ensures that the new spindle is an exact fit with the handle.

If the damaged spindle is beyond repair, it could be necessary to replace it entirely. Home centres sell generic substitutes but if the window design is unusual you'll require contacting a cabinet maker or woodworker who can recreate the exact piece. Once the spindle has been installed, it can be attached to the handle. Place the screw holes on the handle to the existing screws in the frame. Once the new handle is in place, you'll be able to operate your uPVC window.