Ten Things Everyone Misunderstands About The Word "Kia Picanto Key Fob Replacement." How to Replace a Kia Sportage Replacement Key

For many Kia models keys, there is the keyless entry system that is built into the key. This key is similar to the remote control, and can be exchanged with a Kia dealer.

Key fobs may stop working due to a variety of reasons, such as the battery being dead, worn-out buttons signal interference, or water damage. Here are some tips to assist you in getting your Kia sportage replacement key to work once more.

How do you replace the remote key or smartkey

The battery in your Kia's intelligent key will eventually need to be replaced, regardless of whether it is a remote key, a push-to-start key or a standard metal key that does not contain an electronic transponder. This is especially when your car shows a message that states the smart or remote keys are in poor condition.

Luckily, it's a relatively simple process. To replace the battery of the key fob remove the mechanical key from the slit in the back of the key fob. Next, break the cover. Inside the key fob, there will be a small screw that holds the battery in its place. Take out the old battery by removing the screw using a small screwdriver. Then, you can insert the new battery and close the slit inside the key fob.

Once the key fob has an updated battery Test it by pressing the lock and unlock buttons. If the doors unlock and lock according to your expectations, then you're good to go! You can now take advantage of Kia's hands-free lock/unlock function when your fingers are cold or you need to go on errands around Brandon.

Note: Certain key fobs may need to be programmed (transponder chips or smart keys). This requires a specific programming machine that only the dealer or automotive locksmith can access. Other keys (non transponder keys made of metal) are not required for programming. If you're required to reprogramme your key, you'll have to note the key code's number on the key code tag.

How do you replace a dead battery?

If your Kia key fob is not responding when you press the lock or unlock button on the fob, this is a signal that the battery needs to be replaced. A battery that is not functioning properly can cause other issues, like the check engine light flashing or the engine not working properly. Fortunately, replacing the battery on the key fob is a relatively easy DIY project that requires just the most basic tools.

Before you begin, make sure that your vehicle is turned off and all doors are closed. Locate the small metal or plastic piece that is on the bottom of your key fob and gently jiggle it until the metal key is released. The key can be put into the driver door handle to unlock your car.

To replace the battery in the key fob, you must remove the rear cover. Utilize a plastic plier tool to loosen up the latch that holds the black negative cable. Take the old battery out, and then orient the replacement battery to ensure that its "+" side faces you, and the "-", negative side is facing the fob's electrical contacts. Push the new CR2032 battery straight into place, avoiding excessive force to avoid damaging or bending the contacts made of metal.

Once the new battery has been installed and the key fob is turned on, turn it off and then turn it on in the ignition several times until the door locks cycle. Then kia picanto key programming can test your Kia key fob to determine whether it's functioning properly again.

How do you replace a smart keys

You can have the standard keyfob or Smart Key based on the model of Kia Sportage. The difference between the two is that the smart key comes with a small mechanical key blade in it, whereas the standard fob isn't equipped with. Both kinds of key fobs contain batteries that will eventually have to be replaced. This is an easy process that takes just two minutes.

Before you start before you begin, ensure that you are on a flat surface with sufficient lighting and that your Kia is not on. Also, keep in mind that there are tiny parts inside the fob that could be snagged if not vigilant.

The first step is to locate the small release button that is located on the lower backside of your fob. This will be either a circular or rectangular slot. Once you press this button, the mechanical blade will be released and you will be able to open the key fob.

Once you have the key fob opened, you can simply remove the old battery and replace it. The new battery should be a CR-2032 and can be purchased online or at your local auto parts store. After installation with the battery, you should be able to lock, unlock and start your car using your key fob - even if the engine isn't running!

How do I replace the mechanical key?


The Kia key fob is a wonderful feature that lets us lock and unlock our car with the press of one button. Like any other device that is used, the Kia key fob may have issues. There are steps to take to solve these issues and keep our key fobs in good working order for the long term.

A low or dead battery is one of the most common issues. The fob could be able to cease working or even to stop working intermittently. If this happens then try replacing the battery with a fresh new one.

If this doesn't fix the problem, try using a standard flathead screwdriver to open the fob's plastic casing. Be cautious not to damage any internal components or scratch the plastic. After the battery has been removed, replace it with a new one.

Once the new battery is installed, close and unlock the doors with the mechanical key (every Kia fob comes with an emergency mechanical key that can fit in the slot). Test the key fob to make sure it is working properly. If the key fob isn't functioning, contact a locksmith or dealer to help solve the problem. Make sure they make you an emergency key that functions across all trunk and door cylinders, to prevent lockouts in the future.