15 Pinterest Boards That Are The Best Of All Time About Repair Car Keys How to Repair Car Keys

The car keys aren't big and might not seem to be important, but they are essential for the proper operation of your vehicle. Replacing a traditional key or a modern transponder key can cost up to $200.

However, there are ways to fix your car keys at home for less than. This article will discuss the most frequently encountered car keys problems and the DIY solutions.

Dead Key Fob Batteries

The remote key fobs that are included with cars make it easier than ever before to open the trunk, doors and tailgate. However, the battery inside the device can fail. However, there are a few techniques that can be employed to resolve this issue in a pinch.

First, determine if the car is in ignition mode. If it is, the key fob's battery could be low rather than dead. To test this, press the button on the fob against the ignition button on the vehicle. If this does not work, the battery is probably fine and needs to be replaced.

To replace the fob battery, start by prying the case open using an instrument like a screwdriver, or watch-type tool. Be cautious not to put too much pressure on the fob since this could cause the fob's to split in two. If the fob isn't opening, try using your pry tool more than once around the outside of case.


Open the electronic portion of your car once you have removed the mechanical key. Then, you can insert the replacement battery and then snap the shell together. If the key fob doesn't work after this, there may be a more serious problem with your car's remote start system that requires a professional to diagnose. A reputable mechanic will able help you if this is the situation. If you require assistance with your car or vehicle, you can get roadside assistance.

Broken Key Ring

There are a few options to do if your key fob doesn't function because the ring is broken. First, you must check to see if the broken piece is still inside the ignition. If it's still in there the ignition, take it out without causing damage to the ignition lock or the door lock. If repair car key have trouble taking it off, call a locksmith for help. They have special tools that allow you to safely remove the damaged key from the ignition.

A broken car key could also be the result of corrosion on the plastic frame or circuit board. You can clean the circuit board by using a cotton swab and rubbing alcohol. This will remove corrosion and ensure the contact pads aren't damaged.

You can repair a damaged ring by using a thick wire or nail to seal the hole. Superglue can be used to fix damaged key rings. After cleaning the ring with a wet cloth, apply a small amount superglue to each end of the nail or wire. Allow the pieces to dry, and then press them into place. These DIY solutions can appear appealing, but they're really just a stopgap measure. For long-term repairs, it's recommended to work with an experienced locksmith. They have the tools and knowledge to fix a broken car key quickly and efficiently. They can replace the battery and reprogram the key fob if necessary.

Broken Key Blade

Key blades can break due to wear and tear. If this happens, you should probably buy a new one. The issue isn't as serious as you might think at first glance. car key and repair is that the metal blade snapped off the case.

Spraying lubricant into the keyhole is one way to fix it. You can then make use of pliers or tweezers grasp the damaged end of the key and pull it. You could also employ a magnet in the event that the key is magnetic. Be cautious not to use a magnet on an ignition key because it could cause the tumbler of the lock to break.

If you're unable to remove the broken piece from the key, contact an expert locksmith immediately. They have the right tools to safely extract keys without causing any further damage.

Super glue can be used to fix a snapped lock. Apply a small amount of glue to the edges of the break and press them together. Make sure the glue has dried before inserting the key into the lock. This method isn't reliable and you might have to repeat the process a few times before it is successful. In addition the super glue may not be enough strong to keep the key in place. This is more of a temporary measure rather than an option that can last.

Broken Plastic Loop

If the plastic loop on your key fob is damaged it can render the key useless. Fortunately, this is a fairly simple fix. As a replacement alternative, you can opt for wire that is thick or a finishing nail. Drill two holes into the damaged loop of plastic for each end of the wire or nail. Cut the wire or nail to key width and put the superglue drop in each hole. Press the nail or wire into the holes and let them dry.

Another option is to purchase the replacement shell from a locksmith that sells them. They can transfer the programmable portion of your key into the new shell, and cut new blades for a fraction of the cost.

It's not the ideal solution, but it will help you get back on the road in case your key broke in half. However, it can be difficult to repair the key blade if it's in the ignition. If you're not cautious you could make use of a hair clip or a needle to remove the broken part from the ignition. Contact a locksmith who has special tools to safely remove damaged keys from ignitions. They can also make you new keys that have the proper cuts for your ignition and ensure it works perfectly when it is put into the lock.

Broken Master Key

If a key breaks inside the lock, you'll have to find it before it's completely destroyed. There are a variety of methods you can employ, such as using lubricants and tools like needle nose pliers and tweezers. These tools can take a small piece of the broken key and pull it out.

Spray the inside of the lock with WD-40 or graphite powder. You may also try the hacksaw blade method which involves carefully moving the blade down the edge of the broken key, and hooking onto some of the 'teeth'. If remote key repairs are able to do this you will be able to pull out the broken key from the lock.

Many hardware stores sell tools for key extraction that spiral. This tool has a thin flexible rod with spiral threads that can be placed in the keyway and then bent to form the broken part of the key. Once it has caught onto the serrations, you can twist the bar around and then pull it against the broken part of the key.

Before contacting a locksmith try to get rid of the broken master key. If you're unable to pull an item out, you need to call in the big guns and get a locksmith to cut you a new key and reprogram it to the transponder of your car.