The Timber Sash Windows Cambridge Success Story You'll Never Be Able To
Door Hinge Repair Cambridge
Door hinges are a minor element that can have an enormous impact on the function and appearance of your doors. Replacing hinges that are squeaky is a quick and inexpensive upgrade that can boost your home's curb appeal.
A common method to fix hinges that are squeaky is to make use of petroleum jelly or bar soap. Simply rub the item on the hinges until it's coated.
Replacement Hinges
When they are worn out or broken, hinges can cause significant damage. The good news is that hinges are easy to replace and don't require any special tools. It is essential to choose the right hinge for your home. This will ensure that your door closes and opens easily. If the hinges on your door aren't working properly, call a professional immediately to repair them.
A faulty hinge can cause the door to warp or pull away from the frame. Most often, this is caused by incorrect use or an excessive amount of weight. Lubricating your hinges is essential to prevent this. This will prevent the hinge from rusting, or squeaking and will prolong the life of your doors.
There are many different kinds of hinges and each has its own benefits and disadvantages. The simplest hinge is the butt joint that is attached to a door by putting pins on each side. This hinge is perfect for doors that are light in weight since it does not require much strength to open or close. The butt joint is more prone to damage than any other hinge.
It's best to use continuous piano hinges for heavier doors. This type hinge is positioned on the door and extends the entire length of the door, allowing it to open and close with ease. This type of hinge has the benefit of not needing the use of a center support and is more stable.
The pivot for the storefront door is another typical hinge. It permits a door to pivot from a single point at the top or bottom of the door. These hinges are often found in commercial buildings and are hard to fix if damaged. A professional can help with this issue by mounting a new pivot hinge or replacing the existing one. The cost of hinges will vary depending on the type.
Loose Hinges
If hinges aren't tight they will cause the door to hang crooked and could even begin to scrape against the floor, which is annoying at the best. With a few simple tools, anyone can fix loose hinges. In most instances, tightening screws on the hinges will fix the problem. However, in some situations, the screw holes could have been stripped and they won't stay tight. If the screw holes have become stripped and you need to drill them and then plug them with wooden dowels or glue coated matches made of wood.
To stop your door hinges from getting loose, you must relubricate them and tighten them regularly. It is also important to look for any signs of damage to the hinges. If you spot any chips or cracks on the metal, it may be time to replace the hinge. It's also recommended to replace the hinges if notice that they are starting to stick or bind when you close and open the door.
The most frequent cause of hinges breaking is wear and tear due to continuous use, but without proper tightening or lubrication. This is particularly relevant for doors that are used frequently by children, as they might hang from the handles of doors or swing the door on the hinges. This puts an unnecessary strain on the hinges, which can cause them to become loose and eventually falling out completely.
If the hinges are loose, you can tighten them up with a screwdriver. However when the hinges are loose for an extended period of time, the constant movement of the hinge plate and screws will start to enlarge holes in the area where screws are. The screws will cease to be useful in the event that they fail to remain in place. To fix this, simply put the bare end of a wooden match into some regular carpenter's glue and then tap it with a hammer, working the glue into the hole as much as it is possible. It's likely that you will require a few of these glue-coated matches to fill the hole.
Rusty Hinges
Rust can cause problems when it comes to hinges on doors. This is particularly the case for doors that are older. It can make them look bad, but more importantly it can cause the hinge to break and fail, posing a threat to people who use the door. It is possible to save an old hinge by doing some work. The first step is to take the hinges from the door, and then clean them of any gunk. After the hinges have been cleaned they can be oiled and used again.
Modern doors are constructed from metal alloys or brass that don't easily rust. Some people choose to use hinges from the past because of their beauty and long-lasting. However they are more susceptible than modern ones to rust. The best way to prevent this is to prevent the hinge from rusting in first place.
The most efficient method to do this is by regularly cleaning the hinges with steel wool and a little water, especially if they are wet. If you keep doing it regularly, rust will not be a problem for your hinges for doors.
If you're looking to go further, try using stainless steel for your hinges. In contrast to iron, stainless steel won't rust and can provide your home with modern look. If you aren't able to replace the hinges, however the best way to stop corrosion is to keep it off your door hinges by periodically scrubbing them down and then applying lubrication.

When you're removing the hinges, it's best to remove them completely so that you can get into all the little nooks and crannies to scrub off any corrosion. Once the hinges are cleaned, you can use an oil-based mixture with vinegar to lubricate them and protect them from corrosion. This is a cost-effective and simple solution that is easily accessible in most homes It's a good idea to give it trying before you think about replacing your hinges.
window repair cambridge that won't close
Sometimes doors can become misaligned in time due to the normal expansion and contraction of wood. This can cause the door to catch on the corners or latch when you close it. A little bit of work can often fix these issues. If you can tighten the hinges and fix the issue the door will close correctly again.
Begin by looking over the hinges to find any loose screws. Loose screw can cause a hinge leaf to sag creating an opening between it and the jamb. This can cause the latch not to reach the strike plate's hole, and lead to a jammed door.
To fix this, remove one of the hinge screws and slide a strip of cardboard (we prefer the backs of old legal pads) between the hinge and the door jamb. Then, screw the hinge back into position. This will widen the gap along the hinge's side and narrow it down on the latch side and allow the latch to pass through the strike plate. Repeat the procedure until the issue is solved.
If you're still having trouble, you can hammer or shim the strike plate in order to align it with the latch hole. If this is the case, a some paint and wood filler is usually enough to hide the changes.
Damage to the physical structure or prolonged use can also cause the strikeplate to become bent or warped and cause it to strike the edge but not go enough to secure the door. Apply lipstick to the latch and then stick a stripe of masking tape to the strike plate. Close the door and then open it. The lipstick should leave a mark on the tape at the point that the latch meets the strike plate hole. If the mark is below the hole, your latch needs to be moved upwards.