5 Tools Everyone Who Works In The Boarding Up A Door Industry Should Be Making Use Of How to Go About Boarding Up a Door

Protecting investment properties that are vacant from the elements is feasible by putting up a door with a board. It's not a guarantee against all damages however it can help to prevent some of the problems associated with severe storms.

The boarding up of windows and doors can also deter burglars and vandals. However, it can be expensive and time-consuming to put plywood boards over the openings on a house.

Take a measurement of the door


The first thing you'll need is an accurate tape measure. It is also advisable to have an extra chair or ladder in case you have to see more clearly at the top of the frame. If you have to use these tools, make sure to wear gloves and goggles.

Once you have the measuring tool, start by taking the door's width measurement. This can be accomplished by running the tape measure horizontally across the door. Be sure to remove all other parts of the door, for instance the sweep, when measuring. Then, determine the height measurement by measuring up from the floor to the existing sill plate or lintel. It is essential to take measurements in several places, particularly when measuring doors that are older as they may not have a perfect rectangular shape. If the measurements are different, use the largest number.

You'll have to determine the dimensions of the frame after having taken measurements of the length and width. Ideally, it should be 2 inches greater than the door's width and 1 inch thicker than the door. 2'' higher. This will give you plenty of space to move the frame and door to fit.

When you're ready to take the door frame's width and height measurements It's recommended to remove any trim or casing from around the door jambs so you can see the studs that are behind them. This will allow you to measure the exact gap between the frame's studs and the edge.

After you have removed the trim, measure the length of your door frame using the tape measure. The frame should be measured at three different points and use the smallest measurement. You should also measure the frame's height from top to bottom, on both sides. Use the shortest measurement to determine the width of your door.

If you're having issues with these measurements it's best to speak with an expert and have them come to your home to measure for you. They'll be able to determine the exact kind of door and size you need and how to prepare the frame to accommodate the door you want to buy.

Cut the Plywood

A door frame is typically comprised of a set of thin boards or studs that create a hollow space surrounding the door. The typical door is held in place by two hinges that are fixed to the studs. This means that, if you wish to restore the door, it's necessary to remove the door from its hinges over the course of a few days. Placing plywood in the door's opening is a great method to enclose a door and prevent insects from entering the home. It is simple to do this without nailing or screw the plywood to the frame of the door.

Plywood is affordable, simple to work with, and looks stunning when completed. It is the perfect material to use as a temporary solution for a problem where you need to remove an existing door in order to refinish or install the new one. It can also be used to secure the opening of a room being renovated, such as an excavation site or basement.

Start by taking measurements of the width of the door opening and the height. Mark the measurements on the plywood using a utility knife and a drywall square or other straight edge of metal. Next, snap a chalk line across each of the lines you have marked to indicate where you need to cut. Utilize a circular saw to cut the plywood into the required size.

It is important to protect both your ears and eyes while cutting plywood. Wear earplugs or protective goggles when you can. It is also important to use a sharp blade with a lot of teeth, which will permit you to cut quickly and with minimal tear-out. To avoid cutting pieces of wood from the edges of the cut, use a small block of wood as a template to guide the blade, and hold it only a hair's length away from the mark when cutting.

An effective way to hold the plywood in place without fixing it to the studs is to attach a pair of short braces at each end. boarding up windows service that is inside and the other one on the outside of the door. Then, place the deck screws in each of the holes, and tighten them using an open-end wrench.

Fasten the Plywood

It's time to attach the panel to the frame after you have the wood sheet cut to the right dimensions and the holes for the rails and stiles of the door frame are predrilled. This is a simple project that does not require any extensive carpentry skills provided you follow the correct procedure and use the right tools.

Start by setting up a worktable near the doorway, with two sawhorses and 2-by-4 framing lumber at each end of the table. Lay the entire sheet of plywood flat atop the sawhorses using the marks left by the measurement process to guide you for cutting. Mark the lines using the help of a utility knife, a drywall square or any other metal straight edge. This will act as a guide to the saw blade, and prevent splintering of the plywood when you cut it.

Wear eye protection and use a circular table saw with a fine-toothed blade to cut along the scored line. Then, sand the edges of the plywood panel with 120-grit sandpaper. This will smooth the panels and remove any burrs from the saw cuts. After sanding, apply a layer of wood sealer to the plywood panels and let dry according to the instructions of the manufacturer.

Install the hinges on the door frame. If you're using a hinge with a T-hinge drill holes in the outer face of your door for the strap portion of the hinges. Then, you can screw the hinge's outside edge to the frame with the screwdriver. Repeat the procedure on the inside of the door for the remaining hinges, being cautious not to tighten too much on any of them, or the hinge could shift.

If you have a single hinged T on your outside door you can make it easier to close by putting a wire through the loops of the exterior hinges. Bend a piece of tie wire in half, and put it through the two holes on the exterior of the door. Then connect the wires to pull them tight and lock the door.

Install the Plywood

Place the plywood in the door's opening according to the measurements you took. Change the header of the frame (top) and the sill. Utilize a level and make sure that there is no slop between the sill and the header. If it's not perfect then put a second shim in the area you need it and repeat the procedure until you've got the sill and the header to be plumb.

After the plywood is in place, fix it using the stainless-steel hinge bolts and wingscrews. It's a good idea to make use of a screw gun with an attachment for a hex-head to prevent stripping the head of the screws.

If you live in a house with studs running along your doorway, you could drill hanger bolts into every framing piece. This is a much easier task than drilling the hole using the aid of a drill or drywall saw.

After installing the plywood after installation, take measurements of the width and the height of the door opening. If necessary, cut the bottom of the plywood to fit the size of the door frame. Cut two pieces of 1-by-6 framing lumber as braces that attach across the upper and lower ends of your door. Cut along the lines that are marked on the plywood with a circular blade with teeth that are finely tipped. Wear eye protection. Get rid of any splinters that may have formed in the cuts with the help of a sanding block.

After you've placed the braces after you have positioned them, use two pairs of 2-inch finishing nail to attach each brace to the plywood. Counter sink all nail heads when you're done. Seal the braces using a high-quality wood sealing product, such as the wipe-on polyurethane from Minwax.

If the door is too big for the doorway, you could add a piece of decorative molding to fill in the gap between the jamb and the door or you can alter the size of the opening. In many cases, however it is less expensive and easier to simply buy a new door. This can also alleviate any problems you might have had with the original door if it was damaged and could no longer fit the opening.