10 Facts About Saab 93 Key Fob That Can Instantly Put You In Good Mood How to Replace a Saab 9-3 Key

The Saab 9-3 has a great amount of appeal for drivers. It offers good visibility and an impressive performance engine. It also has an excellent safety rating.

It is important that you have two keys that work for your vehicle. It is costly to replace a key in the event that you lose it.

How to replace the ignition Key on the Saab 9-3

You'll must replace the car key when it doesn't turn. This guide will walk you through how to do it on the Saab 9-3. You will need a replacement key, a new reprogrammable battery, and a new key-fob case.

Most modern Saab models use transponders instead of a traditional key to unlock the car and begin it. saab 93 replacement key with this is that the reprogrammable battery in the key-fob will eventually wear out and will not hold a charge anymore. This is especially when you use the same key for the lock you have.

The good part is that the battery is easily replaced by an experienced locksmith. You can also do it yourself if have the necessary tools and a little bit of patience. The first step is taking the key-fob out. This is done by inserting a flathead screwdriver into the slot located in the middle of the case. You must work slowly, as the plastic is thin and can easily be damaged.

Once the case is opened then you can prepare the new key by combining the lower half of the old key with the transponder and banana on the new key. This will ensure that the new key is mated to the CIM properly, which can make a huge difference when replacing the only key for your Saab 9-3.

How to replace the ignition Key on the Saab 900

Unless you have two keys, you will need to remove the dashboard and steering wheel in order to access the ignition. Begin by disconnecting the negative battery cable. After the battery has been disconnected, it is possible to remove all the trim pieces and dashboard pieces that surround the steering wheel. Once the dash has been removed, you can push a screwdriver through the opening at the back of the ignition switch and take it out.

The ignition cylinder has a key lock that could stop the car from starting if a key isn't there. If the ignition switch on your 900 doesn't work properly, you should check whether the key is in the lock or inside the barrel. It's also recommended to rotate your keys on a regular basis and clean them regularly so that one doesn't become bent.

Saab cars are different from other cars because they don't have traditional metal keys. Instead, the car can recognize the key fob's electric signals through a special chip in it.


If you lose only one working key fob your dealer will charge the cost of replacing your computer module (also called the CIM). However, we can reprogram your existing computer's EEPROM and set it to accept new keys without replacing it. This will save you up to 50% of what the dealer charges! This is the SAAB Key PROGRAM. Find out more information about it here!

How do you replace the ignition Key in the Saab9-5

The metal component of a traditional Saab key is simple to duplicate, and it's also not a major obstacle against vehicle theft. The electronic part of the key fob has a chip that can recognize the car when the key is put in the ignition switch.

Saab's anti-theft system has relied on this technology for over a decade. It's not as secure as a physical lock on the door, but it does make stealing your own car significantly more difficult. This is why every Saab owner should keep an extra key available.

Most new Saabs come with two keys right from the factory, however you can buy more keys from the dealer with a handheld computer referred to as a Tech-2. The cost can be under $400 for the transmitter+transponder (different than the metal key blade/shell that opens the doors and turns the ignition cylinder). The only exception is for NG 9-3 cars, which are equipped with modernized, more modern features that require a separate key-fob and operate using a different procedure.

If you lose all keys and the dealer replaces your CIM or TWICE modules and charge you a premium for it. We can reprogram your computer's EEPROM to accept new keys, without replacing expensive modules.

How to replace the ignition Key on an XC90 Saab

It's possible to replace your SAAB key fob if you're experiencing difficulty turning the barrel of the lock. The process is relatively simple and doesn't require you to visit a dealer. You can complete the process at home using a few basic tools.

In the beginning, you'll need to prepare the new key. Before you begin, ensure that the anti-theft system has been disabled by placing blocks on your rear wheels and engaging the handbrake. Next, put the key in the ignition and turn it to the on position, which activates the accessories, but doesn't start the engine. Repeat this 5 times, and then put the key in the "on" position.

The next step is to find a new case for your key fob. They are readily available at many auto parts stores and are generally quite affordable. They can be purchased without electronics based on the model.

To open the case, insert an flathead screwdriver into the slot that is in the middle, and gently work it. The case should break easily and, once you have it, you'll be able to gain access to the internal electronics. To take the electronics out, employ a small screwdriver and attempt to pull them out with a gentle force.