15 Funny People Working In Locks Repair In Locks Repair How to Tell If Your Locks Need Repair

Lubricating your door lock can aid. If it is wiggles when you insert the key, it's time to call for professional lock repair or replacement.

In some cases, a newer, more secure lock might be more affordable than trying to fix an old lock.

Damage to the Cylinder

The cylinder may be damaged if it feels stiff or when the key doesn't move smoothly. A damaged cylinder can make your door open to burglars. It is recommended to repair it as quickly as possible. You can try lubricating the lock to see if this helps however, if you are unable to fix it by yourself then a locksmith should be contacted.

Rust and corrosion are among the most frequently cited causes of cylinder lock problems. You can stop it by regularly painting the lock surface with an anti-corrosive coating. Also, ensure that the weather strip is in good working order. This could cause water to enter the cylinder and weaken it over time.

Another issue that is common is when the cylinder is out of alignment with the keyhole on the door. This could be due to a number of reasons, including loose screws or a misaligned keyway in the handle. To fix it you'll need to take out the screws that attach the cylinder. Then slowly adjust the cylinder. Be cautious not to tighten them too tightly, as this could damage the parts.

Use a graphite lubricant to ensure your cylinder runs efficiently. This is typically found in hardware stores and can be applied directly to the cylinder. The lubricant will help the key turn smoothly and will also help prevent future lock issues.

You may have to replace the cylinder if it is completely damaged. This is a relatively simple task you can complete at home. The first step is removing the faceplate. Once that's done you can then begin to disassemble the lock and cylinder. After removing the cylinder from its mounting, you should note any set screws holding it in the position. These are important to be aware of for reassembly later on.

Finally, make sure you use a screwdriver that has a fine tip for getting into small spaces within the lock. You should also keep a few plastic ziplock bags to store the components you take out for later reference.

Knobs or Handles that are Leap

Over time, door handles or knobs will get loose. This can cause a huge problem for employees as well as customers. This issue is usually easy to fix, and does not require an emergency locksmith service.

In general, loose doorknobs can be caused by the same factors that cause locks to move and pull away from doors: wear and age loose screws; incompatible components. It's also possible that your home or business might have moved slightly. This could affect the way that the door handle is attached to the lock.

It is possible to fix loose knobs or handles but you must have the correct tools. Also, be car central lock remote repair not to tighten the screw too much. This could cause damage to the doorknob or handle. It's also a good idea to have a second hand to help you twist and tighten the doorknob.

First, it is crucial to locate the screw that is loose. The screw is usually hidden beneath a decorative cap that covers the mounting rings for the lockset. To take off the decorative cover and reveal the mounting rings for the lockset, you will need to press a button or lever using an awl. The nut can be tightened by turning it counterclockwise.

Some modern doorknobs are made with a different method of fixing. They use a device known as a detent and are attached to the door with hidden screws. This type of fastener may be slightly more complicated, but it can be fixed easily using the same methods previously.

After the screw has been tightened, it is recommended to put a washer on top of the screw. This will prevent the screw from becoming loose in the future. This is particularly crucial for wooden doorknobs which may have a damaged screwhole due to repeated use. Washers can be found at any hardware store and are an easy and quick solution to any problem you encounter. Choose a washer that matches the screw in your doorknob.

Keys that are poorly cut

Keys that are not cut properly are the most frequent cause of a key not turning in your lock. This could be because of a poor copy made by locksmiths or the original key getting worn down over time. It is crucial to only employ a reputable locksmith if you require keys copied or to have your locks changed.

A locksmith will always examine keys for the correct cut depth, and ensure that they are evenly distributed across the key. A good locksmith will inspect the lock and pinpoint the problem. They will then suggest a solution, such as replacing pins or adjusting the lock's cylinder.

It is a good idea to bring the key that doesn't rotate when you visit a locksmith so they can check it out in their duplicator. This will make sure that the key is cut correctly, and that it will fit your locks correctly.

If the key is unable to fully insert into the lock, it could be due to dirt or debris that have built up in the lock. Lubricating the lock using graphite or a silicone-based lubricant can aid in clearing tumblers that are stuck or blocked.

A key that was not cut exactly when it was made is a frequent issue. This could happen if someone attempts to make a cheap and quick copy of a key. It is crucial to be sure to work with a professional locksmith who has the equipment and knowledge required to make high-quality copies.

If a key is broken off from the lock, you can try to grasp the broken piece with needle-nosed pliers, or even a pair of tweezers. Be careful not to push the tip of the pliers or the tweezers too far since this can cause the problem to get worse. Also, it will be much easier for an expert to remove the broken piece without causing further damage to the lock mechanism. It is recommended to bring the key that broke to the locksmith, so that they can make use of their duplicator to create the replacement for you.

Sagging Locks

If you're having trouble locking your door It could be because of a sagging lock. This can cause the latch or bolt to get stuck in the frame of the door and make it difficult to close the door. This can cause drafts and create a larger gap between the frame and the door. Both of them can be damaged in time.

You can easily repair locks that are sagging. Usually, you can fix them by tightening screws on hinges. If it doesn't work, then you could try lubricating the lock. You can try using powdered graphite or a silicone-based lubricant. Choose a lubricant that doesn't cause damage to the lock over the course of time.

Another issue that can affect the ability of a door to open and shut properly is a faulty locking system. This could be caused by the door not being set up correctly, or by a climate change that causes the frames and doors to move. If not addressed, this problem can leave your home or business vulnerable to burglars.

It is first necessary to ensure whether the frame and door are on the same plane. If not it's time to move the hinges to the correct height and align.

The next step is to examine the mortise and strike plate. You can adjust the strike plate if it's sliding with a hammer, or chisel. After you've repositioned it test it to see if it is aligned with the latch.


If you're experiencing issues with your lock, it could be time to call an expert locksmith. A locksmith can fix any lock, no matter if it's a Yale lock or mortice lock.

Only certain damages to locks can be repaired. It is not recommended to bend the damaged bolt back into its place, as this will weaken the bolt and possibly cause damage to the cylinder. If you're experiencing serious issues you should call an expert. They'll be able assess the severity of the issue and give you a better idea of what options you have.