Where Will Fiat Panda Key Fob Replacement Be 1 Year From In The Near Future?
Reasons Your Fiat 500 Key Fob Won't Work
A key fob for the Fiat 500 makes it easy to open doors and start your vehicle. There are many reasons the fob could stop working. These include a dead battery or damage to the receiver module, issues, or interference.
This listing is for a NEW replacement Fiat Flip Key Remote that looks like the Ilco brand. It has to be professionally programmed (click here to find local locksmiths in the automotive industry). Includes lock, unlock, and trunk buttons.
Dead Coin Battery
The most common reason your 500 key fob won't work is the battery is dead. Modern key fobs have a limited range of operation, and must be within only a few feet from the vehicle to function. If you're far from your vehicle and press the keyfob button, it will not respond, and display the message "Key Fob Not Detected".
If this happens, simply replace the battery on your coin cell (Part number CR2032) with a fresh one from a reputable brand such as Panasonic, Duracell, or Energizer. You can find them at the local hardware store or on the internet.
You can test the battery of your coin-cell by pressing the buttons while you are standing close to your Fiat 500. The parking lights should blink and the key fob will operate the lock and unlock switch.
If the fob's key doesn't function after replacing the battery, it may have water damage that prevents it from communicating with the receiver module in your vehicle. Water damage can occur in a number of ways, ranging from the slightest splash to submerging the fob in salt water at the beach. If you suspect that your fob has been exposed to water, put it in a dry rice bag to pull the moisture back out. If this doesn't work your fob may require reprogramming by an experienced locksmith or dealer.
Water Damage
Water damage can occur when you immerse the fob into the ocean or wash it in a machine. Saltwater poses a particular risk to the circuit board of the fob and can cause it to short out and eventually end up dying. It's not good to submerge the fob in water however, but don't give it up if you accidentally drop it in water or forget to take it out of your pocket.
First, remove the battery. Clean the electronic chip using isopropyl or a similar product and then dry it thoroughly before replacing the battery. Check the fob again to see if it is working. If the key isn't working, it may need to be reset.
new fiat 500 key is usually done by a dealer or professional auto locksmith.
If the key is more recent and was not programmed to your vehicle, it will likely need to be replaced completely. A professional locksmith for cars will be able to complete this process. The locksmith will need the key to be cut to match your vehicle's ignition. The locksmith will also have to reprogram your fob into the vehicle's system. This is a simple and cost-effective procedure that can be completed on the same day.
Receiver Module Issues

The 500 key fob you have may stop working because it is out of range. The remote's range is of 30 feet, which means should you be too far from your vehicle it will not respond to your commands. It can be solved by moving closer to your vehicle until it begins responding.
If your fob doesn't work after replacing the battery for the coin, also called a "button", "watch" or "button" It may be due to a malfunction on the circuit board inside. Reprogramming the fob typically resolves this problem. You can find the procedure for most vehicles on YouTube or in the owner's guide.
It could be necessary to replace the clips made of metal that hold the coin batteries in the correct position. If they lose tension, it can prevent your coin battery from sitting properly and cause your remote to malfunction.
In rare cases the fob may be out of the vehicle's sync because due to hardware or software issues. This can be a major problem, but you can usually resolve this issue by visiting a local dealer or auto locksmith to reprogram your fob for you. In certain instances the software might require reinstallation to your body control modules.
Interference
In addition to a dead battery on a coin The key fob might not be able to transmit or receive a signal due to interference. This can happen when the key fob is in proximity to the radio transmitter (cell phones or radar detectors) or another source of electromagnetic radiation. The key fob might not function because of a weak connection with the buttons or water damage, or damage to the internal chips.
If your key fob suddenly stopped working, or you've tried everything at home to solve the issue (e.g. You might have a damaged 500 receiver module in the event that you've tried replacing the battery, reprogramming, or using an alternative key fob. The receiver module, which is located under the dashboard, detects radio frequency signals from your key fob. It converts the signals into electronic commands that are then processed by the vehicle.
There is a simple way to reset the 500's in-board system including the keyfob. Disconnect the 12 volt battery for about 15 minutes by removing the negative cable and then the positive cable. Reconnect the battery. This will erase any remaining electricity, and allow you to restart the computer of your car. This could help you get your key fob to work again. If the problem persists you should consult an expert technician. They will be able to diagnose the exact cause of your issues.