10 Tips To Build Your Peugeot Keys Empire Peugeot 208 Key Replacement

It is best to leave the replacement of Peugeot 208 keys to auto locksmiths who have the necessary equipment and technical skills. They can create and program new keys much faster than a dealership would and at a lesser cost.

If your key fob stopped locking or unlocking your doors it is likely due to a dead battery in the coin. There are other reasons for the key to be malfunctioning.

Dead Coin Battery

A dead coin battery will stop your Peugeot 208 from locking and unlocking, as well as stopping it from starting the engine. In this instance you'll have to make use of the alternative method for starting described in your vehicle owner's manual.

The spark plugs can also be worn out. The spark plugs ignite fuel to start the engine. However they have a short lifespan. If they aren't used enough and they fail, they'll eventually die.

There is a straightforward solution to this problem. The best option is to check the voltage of your car battery using a multimeter. If the voltage is less than 11,5 volts, it's time to replace it. If the battery is corroded it is crucial to clean its contacts. You can do this by lifting the rubber covers that protect both battery terminals and using a wire brush to remove any corroded components of the battery. Then, reconnect the positive pole cables to the negative.


Water Damage

If your 208 does not start and the battery has not fallen flat, it is time to inspect the spark plugs. You may find that they are simply too dirty and don't spark. The spark plugs can be cleaned in the workshop.

Peugeot automobiles use a transponder key that works with the car's immobiliser system. This ensures that only a valid key is able to turn the engine. If the chip inside the Peugeot key is damaged, then it won't send the correct signal to the vehicle.

TheKeyLab is a common problem that can occur due to water damage. This is a common issue in warmer climates where the vehicle is exposed to snow or rain. If this is the case, you should call a reputable auto locksmith who has all of the tools and equipment required to change the key's programming. They'll also have the latest technology and machinery needed to create a Peugeot smart key. The process shouldn't be more than 15 minutes.

Contacts to the battery are not working properly.

Peugeot replaced the old transponder chips with a new model that utilizes electronic components mounted on a circuit board. The new system works great in its initial state, but the circuit boards degrade over time and cease to function properly.

This can prevent the immobiliser chip from working and causing your car to not start. If this is the case, it's a good idea contact a Peugeot specialist or locksmith.

Another common issue is when the battery of the key fob starts to die, this causes the key blade to stop getting into the lock. A locksmith from your car will replace the battery, and then cut a fresh blade for you. This is a quick solution.

Faulty Receiver Module

It could be that the receiver module has a problem If your Peugeot key fob stops working after being dropped on the floor, or exposed to a sudden downpour or accidentally washed. The receiver is responsible for sending radio frequency signals to the onboard computer, which controls the central locking system in your Peugeot vehicle.

Rubber seals on the key fob stop water from reaching the electronic chip. However prolonged exposure to water could break through these seals, causing damage to the chip. Submerging the key fob in ocean water on the beach or throwing it into the pool can be especially damaging because of the high salt content.

If your Peugeot spare key fob doesn't work You'll need the module replaced. This can only be done by an expert auto locksmith or Peugeot specialist. In contrast to other vehicles, Peugeot keys are protected by an exclusive immobilizer system that requires the correct code for the start of the engine. This is why you should only trust an experienced Peugeot locksmith with the task of programming and creating a replacement.

Faulty on-Board computer

The computer on the board of your Peugeot is the one responsible for all of the systems inside your vehicle, from power windows to the airbags. If something is wrong with these systems, it will usually show a code that identifies the issue. This code will be saved within the system until the issue is resolved. In most cases, this will require replacing the computer on board.

The most common cause of the warning light for airbags to flash is corrosion or loose connections within the sensor. This can be caused by wear and tear, age or exposure to salt and moisture. This problem should be addressed as soon you can, as an airbag that is malfunctioning could pose danger in the event of an accident.

If your Peugeot is showing a card that is not being detected error, then the battery inside the key fob could be dead or weak. This will prevent the key fob from sending a signal that disarms the standard immobilizer in your vehicle. Test this by pressing the unlock key on the key fob, and then trying to start your vehicle. If it doesn't work, the key battery needs to be replaced.

This user has nothing created or favorited (yet).