20 Up-And-Comers To Follow In The Locks Repair Industry How to Tell If Your Locks Need Repair

Lubricating your door lock with oil may help. If it wiggles around when you insert the key then it's time to call for a professional repair or replacement.

In some cases the case, a newer more secure lock could be more affordable than trying to fix an old lock.

Damaged Cylinder

The cylinder could be damaged if it feels stiff or if the key does not turn smoothly. A broken cylinder can leave your door vulnerable to burglary and should be fixed as soon as is possible. You can try lubricating your lock to see if it helps however, if you are unable to fix it yourself then a locksmith should be contacted.

Cylinder lock issues are usually caused by corrosion and rust over time. You can stop it by regularly painting the lock surface with a protective coating. Make sure that the weather strip is in good working order. This could cause water to enter the cylinder, which can weaken it over time.

A misalignment of the cylinder with the keyhole on the door is another frequent problem. This could be due to a number of reasons, including loose screws or an incorrectly aligned keyway on the handle. To fix this the first step is to take off the screws that hold the cylinder and gently adjust it. Be careful not to tighten them too much, as this could damage the components.

Use a graphite-based lubricant to ensure your cylinder runs efficiently. It is available in hardware stores, and can be put directly to the cylinder. The lubricant will help the key turn easily and also prevent future lock issues.

It is possible to replace the cylinder if it is completely damaged. Fortunately, this is an easy task that can be accomplished at home. The first step is to take off the faceplate from the lock. After removing the faceplate, you can begin disassembling the lock cylinder. After taking the cylinder off its mounting, you should note any set screws holding it in place. It is essential to record these screws for later removal.

The last thing to do is use a screwdriver with a fine tip to get into the smaller areas of the lock. It is also recommended to have several ziplock bags to store the parts that you have removed.

Knobs that are loose or handles

Over time knobs or handles on doors are likely to get loose. If this happens, it can cause a lot of inconvenience to employees and customers. The good part is that this issue is usually easy to fix and doesn't require a professional locksmith service.

Most commonly, loose doorknobs are caused by the same issues that cause locks to move or pull away from the door: age and wear loose screws and the wrong combination of components. It's also possible that the house or business may have been settling slightly. This can affect how tightly the door handle is tacked to the lock.

It is possible to fix knobs or handles that are loose, but you must have the correct tools. Be careful not to over tighten the screw. This could damage the doorknob or handle. It's also a good idea to have a second hand available to help you twist and tighten the doorknob.

It is important to first locate the screw that is loose. It is usually located under an attractive cover that protects the ring that holds the lockset. You will need to depress the lever or button using an awl or the tip of a small flat blade screwdriver in order to remove the cover and expose the lockset mounting ring. It is then possible to tighten the nut by turning it counterclockwise.

Some newer doorknobs are designed using a different fastening method. They use a device known as a detent. They are attached to the door with concealed screws. This type of fastener may be more complicated however, it can be fixed with the same steps.

After the screw has been tightened it is an ideal idea to apply a washer to the screw. This will stop the screw from coming loose in the future. This is especially crucial for wooden doorknobs that can get a stripped screwhole from repeated use. Washers can be purchased at any hardware store, and they are a simple and quick solution to stop a daily nuisance. Just be sure to choose a washer that is appropriate for the screw that is used in the doorknob.

Keys that are poorly cut

Keys that are not cut properly are the most common cause of a key not turning in your lock. This can be a result of a poor copy made by locksmiths or the original key getting worn down over time. When you need to have keys copied or have your locks rekeyed, it's important to use a reputable local locksmith.

A locksmith must always inspect a key to determine the appropriate depth of cuts and to ensure that they are evenly spaced across the key. A professional locksmith will inspect the lock to determine the cause of the issue and then come up with an answer for you, whether it's replacing the pins or altering the lock cylinder.

Bring the key that will not turn to a locksmith so they can test it on their duplicator. This will ensure the new key is cut correctly and that it fits your lock properly.

If the key will not fully insert into the lock it could be due to dirt or debris that have accumulated inside the lock. Lubricating the lock with graphite or silicone-based lubricant will aid in clearing tumblers that are stuck or clogged.

A key that was not cut exactly when it was created is another common issue. This is often the case when someone attempts to create an inexpensive and quick copy from an existing key. It is essential to trust a professional locksmith with the tools and training necessary to make high-quality copies.

If you've got a damaged key in the lock and you want to retrieve it, you can use a pair needle-nosedpliers or tweezers to remove it. You should not insert the pliers' tip or the tweezers too deeply. This could make the situation worse. It is easier for a locksmith to take out the broken piece without causing damage to the lock mechanism. Bring the broken key to the locksmith and have them create a new key with their duplicator.

Sagging Locks


If you're experiencing difficulty locking your door, it could be because of a sagging lock. This could cause the bolt or latch to become stuck in the frame of the door and make it difficult to close the door. This can lead to drafts and cause a greater gap between the door frame and the door. Both can be damaged over time.

It is possible to fix sagging locks. Usually they can be fixed by tightening the screws on hinges. If this doesn't work, you could try lubricating the lock. You can use graphite powder or a silicone based fluid. Select a lubricant that won't cause damage to the lock over the course of time.

Another common issue that could hinder the ability of a door to shut and open properly is a misaligned locking system. This is usually caused by a door that wasn't installed correctly or a shift in the temperature which causes doors and frames to shift. If untreated the issue could leave your home or business vulnerable to robbers.

To fix this first, you'll need to start by examining the door as well as frame to determine whether they're at the same level. If they're not, you'll need to reposition the hinges to the proper height and align.

Next, you'll need to inspect the strike plate and mortise. If the strike plate is sliding out and you want to reposition it, try with a hammer and chisel. After you have moved it back and checked it, make sure it is in alignment with the latch.

Contact www.g28carkeys.co.uk if are experiencing issues with your lock. Locksmiths can fix any lock, regardless of whether it's a Yale lock or a mortice lock.

Remember, only certain types of damage to locks can be repaired. Don't try to bend a damaged lock bolt back to its original position. This could weaken the bolt and could cause damage to the cylinder. It is recommended to contact an expert if you're having serious problems. They'll be able to assess the damage, and tell you what options you have.