How To Survive Your Boss On Car Key Button Repair Car Key Button Repair

A damaged car key button is frustrating. You may need to contact the 24 hour Locksmith Service or purchase a replacement remote.

You may be able save money by fixing your old key fob instead of replacing it. This is especially true if the problem is due to the worn-out switch or defective contact.

Battery

If the buttons on the key fob aren't responding to pressing the buttons, this could be a clear sign that the battery is dying or nearing the end of its lifespan. Fortunately, replacing the battery is a simple task that can be completed on your own instead of hiring a locksmith or dealer to take care of it.

First find the battery compartment. The battery compartment is usually located on the back of the key fob and can be hidden behind a cover which can slide out or an open button that opens the access point. When the compartment is opened then look for the small button-cell battery. It's usually shaped as an oblong coin and is has a plus and minus sign. Remove the old battery and replace it with a new one in its place, making sure that the plus and minus marks are correctly aligned.

Close the compartment and snap the two halves of your key fob. Before closing the door, align and snap the parts in the correct position. Press any of the buttons to confirm that they work properly.


If your remote key fob ceases functioning even after replacing the battery, it might be suffering from other issues that require a different form of repair. The fob's dropping in a puddle could cause it to stop working. It could also be due to a problem with the internal electrical system or the need to be deprogrammed. Take a look at these other automotive troubleshooting methods to determine whether your key fob is experiencing a different issue.

Switches

Depending on the year and make, there are different types of switches on the car keyfob. The older style key has an electronic chip that is visible in the case. The newer keys work by sending signals to your car. Whatever the model of key, the buttons on the key can become worn out or damaged during normal use. This causes them to become difficult to press or even unresponsive. If you press the button with force it can cause further damage. It may also prevent the key from functioning in the future.

If you can't get your key to work, try changing the batteries. If that doesn't help, you may need to clean your key fob and re-adjust the switches. Since these tiny electronic switches spend a lot of time being moved around, they are more likely to wear out than larger components of your key.

The switches feel rubbery and are coated with a film that conducts electricity. The film is prone to fade over time. However, they're tiny and cheap to replace. They're soldered to the circuit board, therefore you must carefully remove the old ones without damaging other components. You can then solder the new ones into and reassemble the fob.

A good way to keep your car key fob from getting ruined is to avoid using it for longer than a couple of hours at a time and to avoid leaving it in visible locations in areas where it is visible. Also, you should find a secure location to store your key when you aren't making use of it.

If the problem persists after you've cleaned your key fob or battery, and attempted to clean it, you might need to contact a locksmith. A professional locksmith can test your key's frequency to see if your vehicle is still able to communicate. They can also open and replace microswitches as well as change cases, and more.

Outer Case

A key fob spends much of its time bouncing around, and when the buttons aren't allowed to move between the case, they could become stuck or break. If replacing the battery or cleaning with an alcohol-based swab and a cotton pad rubbing alcohol don't resolve the problem, removing the case and examining it may be necessary. If the contacts the buttons touch aren't an ideal fit, or if they are damaged, adjusting them could be the only solution.

Rubber buttons may wear out over the years. The rubber is stretched and nails pierce it, and the buttons become difficult to press. This can cause the key to fail, and in this case it's time to get an entirely new case or buttons. This repair involves disassembling your remote, locating the button switches on the board, heating the solder, and then carefully taking them off. The new buttons are then connected to the circuit board. car remote key repair The Key Lab is then reassembled and the horse shoe key blade piece is attached. The new buttons should be snugly fitted inside the case to stop them from falling out.

Inner Case

Over time the buttons on your key fob can become damaged or stuck because of the continuous rubbing and accidental pressing. Utilizing metallic tape and a hole punch you can often quickly fix this problem in the event your car isn't at home and the key fob doesn't work and allows you to open the doors, but not start the engine. This quick fix could enable you to safely get back to your car and continue your journey.