クライアントは購入前にHPE0-V14トレーニング資料を自由に試してダウンロードして、製品を理解し、購入するかどうかを決定できます。製品のウェブサイトページには、HPE0-V14学習に関する質問の詳細が記載されています。テストバンクから選択されたすべてのタイトルの一部であるデモと質問と回答の形式を確認し、教材のWebサイトページでソフトウェアの形式を知ることができます。
トピック | 出題範囲 |
---|---|
トピック 1 |
|
トピック 2 |
|
トピック 3 |
|
トピック 4 |
|
Pass4TestのHPE0-V14トレーニングテストの利点の1つは、無料の販売前体験をユーザーに提供できることです。HPE0-V14学習資料ページはサンプルの質問モジュールを提供します。 HP購入する前に、ユーザーはさらにHPE0-V14のBuilding HPE Hybrid IT Solutions試験準備を使用します。 同時に、提供するサンプルユーザーがPDFデモを無料でダウンロードできる方が便利なため、販売前の体験は他に類を見ません。 そのため、HPE0-V14学習教材の効率性を把握し、間違いなく選択することを決定できます。
質問 # 36
You need to create a dynamic bridge-aggregation group on a FlexFabric switch to ensure the ports are automatically configured with the applicable bridge-aggregation interface configuration Drag the steps on the left Into their appropriate order in the answer area on the right.
正解:
解説:
質問 # 37
Which tool provides a report on the current usage levels and life span of some installed read-intensive flash drives?
正解:D
質問 # 38
A customer has requested that you provide them with an architecture and bill-of-materials for a stack of top-of- rack switches. The customer has 34 HPE DL360 servers in the rack, each with four 1GBASE-T Ethernet ports which need to be connected to the network.
The customer is upgrading 50% of the 1GBASE-T Ethernet ports on the servers to 10GBASE-T Ethernet ports and needs the switching to support the upgraded servers. They are opposed to a chassis switch, and want to keep the number of managed devices on the network to a minimum.
Which architecture meets the customer requirements?
正解:B
解説:
Needs 4 switches for port count, customer wants minimum of managed devices so one stack, VSX only supports two switches so must be an IRF based stack. As to ShaunSong's comment, 10GBaseT ports also negotiate 1000BaseT so are inherently 1/10Gb capable.
質問 # 39
Read the question, and then refer to the exhibit.
<Switch-A>display interface Ten-GigabitEthernet 1/0/1 Ten-GigabitEthernet1/0/1 Current state:
Administratively DOWN Line protocol state: DOWN IP packet frame type: Ethernet II, hardware address:
d894-03fb-793d Description: Ten-GigabitEthernet1/0/1 Interface Bandwidth: 10000000 kbps Loopback is not set Media type is stack wire, port hardware type is STACKSFPPLUS Unknown-speed mode, unknown-duplex mode Link speed type is autonegotiation, link duplex type is autonegotiation Flow-control is not enabled Maximum frame length: 10000 Allow jumbo frames to pass Broadcast max-ratio: 100% Multicast max-ratio: 100% Unicast max-ratio: 100% PVID: 1 MDI type: Automdix Port link-type: Trunk VLAN Passing: 10, 20 VLAN permitted: 10, 20 Trunk port encapsulation: IEEE 802.1q Port priority: 0 Last link flapping: 0 hours 0 minutes 18 seconds Last clearing of counters: Never Peak input rate: 78 bytes/sec, at
2011-03-31 04:55:57 Peak output rate: 15 bytes/sec, at 2011-03-30 23:00:57 Last 300 second input: 0 packets/sec 67 bytes/sec - % Last 300 second output: 0 packets/sec 14 bytes/sec - % Input (total): 62670 packets, 8565340 bytes 0 unicasts, 0 broadcasts, 62670 multicasts, 0 pauses Input (normal): 62670 packets, - bytes 0 unicasts, 0 broadcasts, 62670 multicasts, 0 pauses Input: 0 input errors, 0 runts, 0 giants, 0 throttles 0 CRC, 0 frame, - overruns, 0 aborts - ignored, - parity errors Output (total): 3707 packets, 1294835 bytes 0 unicasts, 0 broadcasts, 3707 multicasts, 0 pauses Output (normal): 3707 packets, - bytes 0 unicasts, 0 broadcasts, 3707 multicasts, 0 pauses Output: 0 output errors, - underruns, - buffer failures 0 aborts, 0 deferred, 0 collisions, 0 late collisions 0 lost carrier, - no carrier A customer added a new switch to their network. They connected it using interface Ten-GigabitEthernet 1/0/1.
They are using VLAN 10 and 20 for the devices in their network.
The new switch was fully operational. Then, the customer experienced a power failure later that day and could not reach any device on the new switch after the power returned.
From the output in the exhibit, would could be the issue?
正解:A
解説:
Explanation
"<Switch-A>display interface Ten-GigabitEthernet 1/0/1 Ten-GigabitEthernet1/0/1 Current state:
Administratively DOWN Line protocol state: DOWN IP"
質問 # 40
Refer to the exhibit.
You observed some high temperature alerts on a switch shown in the middle rack of the exhibit. The cooling in the data center is following best practices for the layout in the exhibit. The switch is an HPE 5945 series switch, and all the fans are operating normally. The switch is racked so that its ports face the rear of the rack. The administrator noticed the fan modules have red handles.
What should the administrator do to resolve the issue?
正解:B
質問 # 41
......
私たちは常に新しい知識を習得していますが、常に忘れられているプロセスであり、この問題を解決する方法を常に忘れてしまいます。答えは良い記憶方法を持つことです。HPE0-V14試験問題はうまくいきます。この点について。 HPE0-V14の実際の試験教材には独自の学習方法があり、従来の暗記学習を放棄し、テキストとグラフィックスの記憶方法の組み合わせなど、多様な記憶パターンを採用して、知識の記憶を区別します。 HPE0-V14学習リファレンスファイルは非常に科学的で合理的であるため、安全に購入できます。
HPE0-V14試験準備: https://www.pass4test.jp/HPE0-V14.html