5 Common Phrases About Repairs To Upvc Windows You Should Avoid Repairs to uPVC Windows

uPVC windows are an excellent choice for modern homes. They are easy to maintain, durable and long-lasting. They do not rot or rust like aluminum and timber.

It is essential to clean and oil UPVC windows and doors regularly. This will reduce unnecessary repair costs and improve the efficiency of energy.

1. Broken Glass

If the glass in your window is broken it can cause a huge amount of damage to your home, which can make it very hazardous and possibly fatal. You should take the time to make sure that your windows are in good working order.

For single pane windows it can be relatively simple to replace windows, and the new one will usually fit inside the old frame very easily. If windows with double panes are joined by internal beading, it will be harder to remove and replace the old panes. In this case you'll need find some plastic spacers that help the new pane to fit perfectly into the window frame.

If you're planning to attempt to remove the window panes by yourself it is important to wear the appropriate safety equipment that includes gloves with a thick layer of material and eye protection. You should also lay down a dropcloth before you begin working on the window panes so that any shards fall onto the fabric and not on the floor and could be trampled.

It's a great idea to seal the gap after the glass has been removed. This will stop drafts and water from entering your home until a professional comes out to repair the window. This will also act as a barrier, deterring any intruders from getting access into your home. If the gap is large, you may want to consider using a security door that has an integrated window as it will provide the best of both worlds.

2. Sagging

Upvc windows and doors are a low-cost energy-efficient, durable and long-lasting alternative to timber sash windows. As time passes, they may develop a number of problems, including sagging. A sagging uPVC windows can cause problems with light, draughts, and even security. It's crucial to act immediately if you notice your uPVC windows are falling down.

Repositioning the hinges could help fix a window that is sliding. First, you'll need to open the windows to access the frame. After that, using a screwdriver, you can unscrew the hinges at the top and bottom and adjust them by turning them clockwise or counter-clockwise. After you've repositioned the hinges, close the window and test it for an appropriate fit. If you're satisfied with the fit of the window, tighten the screws to secure them in place.

If you cannot reposition the hinges, you may need to replace the seal. Rubber seals can dry out and lose their elasticity over time, leading them to lose their tightness. It is important to replace your seal as soon as you can to keep your uPVC window watertight and draughtproof.

uPVC handles can also become loose. This is often caused by screws that have become undone over time, but it could be due to the mechanism of the handle getting worn out. Fortunately, it's easy to repair the handle of a window that is loose yourself. First, you'll need to shut the window and perform an initial fitting. The corners of the sash should be aligned with the casing joint. If it does not then you can use the screwdriver to loosen the handle. Then turn the mechanism into position.


3. Water Leaks

If you're waking up to damp floors and mouldy walls each time it rains it is important that you take action. Windows that leak water do are not just a cause for destruction of your home's structure but also hinder your efforts to control the temperature in your home. The most frequent reason for leaks in uPVC windows is that the sealant surrounding the frame has been damaged or is missing.

This is an easy fix that can be done by anyone who is a DIYer with the skills. Based on the severity of the problem the old caulking might need to be removed before a new layer of caulk can be put on. When it is time to uPVC repair, you must avoid 'over-caulking'. This will make your window harder to clean and reduce its energy efficiency.

It is crucial to make sure that the drainage holes are clear of debris and that the sill pan is placed in a way that allows it to drain away from the window. In more serious cases you might need to consider replacing the window.

Mold spots and rotted sills are other signs of water leakage. This fungus thrives in conditions of dampness and can spread quickly throughout the house.

It is also important to remember that if the leak originates from the glass of your double glazed windows it may be more likely to be an issue with the glass seal rather than the frame or sagging. Again this can easily be corrected by a uPVC window expert who can replace the glass seal and regain the full insulation properties of your windows.

4. Faulty Hinges

If your uPVC windows are difficult to open, or loose and blow open with ease It could be the hinges that are at fault. These are easily repaired by any skilled DIYer and can usually be done within a few minutes.

Like any mechanical component, hinges can wear out over time. Changing a window hinge is an easy process but it can be easier with someone else to assist in holding the frame up.

It is also important to verify that the uPVC hinges are opening and closed in the correct direction. You can check this by looking for the arrow on each hinge. This indicates the direction in which the window should open.

Window hinges that aren't working properly could be the result of incorrectly opening the window a certain way or by poor installation at the factory. Sending us a photo via our website is often enough to solve the issue. We are always happy to provide suggestions.

Regular lubrication of the hinges is essential. Applying a light engineering lubricant to the hinges is a good way to do this. We suggest using a lubricant that does not contain solvents, like 3-in-1 Multi-Purpose oil. Regular lubrication can help the window operate and close more smoothly. It can also reduce the chance of windows getting stuck and stop corrosion. It is recommended to perform this every year. WD40 or other solvent-based oils should not be used since they can cause damage to your uPVC windows.

5. Draughts

Draughts can be caused by a variety of different things. Firstly the hinges, again because of wear and tear, may become displaced, which can cause a gap to form where the sash meets the frame. This can be easily repaired by giving them a good clean, but in the event that they are beyond repair it may be necessary to get them re-aligned or replaced. The interlock, which is located on the hinge side of the window, can also be misaligned, and again it may be feasible to give them a thorough clean, however in some instances it could be necessary to have these replaced.

The next common cause of draughts is the window seals, these can become worn down or damaged over time and let air escape through the gaps. Replacement of these with high-quality weatherstripping is a good way to keep draughts at bay. Another alternative is to replace the window with low-emissivity glass, which will help regulate indoor temperatures and again will reduce the risk of draughts.

One of the most effective ways to reduce the draughts in your home is to use a draught excluder, these are typically made of fabric filled with some kind of filler. window repairs near me can be placed on the windowsill on top. These will help to stop cold air from entering and keep your home warm and cosy!

With a little maintenance and repairs, your upvc windows will continue to provide an excellent level of security and insulation for your home. It is crucial to realize that all windows have a life span and there may come the point when it's more economical to replace them than repair them. If you are experiencing issues with your upvc window it is recommended to speak with a professional immediately.