The Most Hilarious Complaints We've Seen About Door Lock Change How to Do a Door Lock Change


Change your door lock is an easy and affordable way to improve the security of your home. However, the process is not for everyone. It requires a certain amount of patience and skill.

You must replace the cylinder that is located inside the knob's body. double glazed window lock repairs is responsible for recognizing the key as it is put into the lock.

Removal of the old lock

First, remove the old lock. This is a relatively easy procedure, but there are some things to be aware of. First, make sure that the lock you choose to install is the right size for your door. This will ensure that it fits securely and doesn't leave a gap around the latch or deadbolt plug.

After you've removed the latch plate look for two screws or bolts on the inside of the casing, which hold the casing and the halves of the lock together. Remove these screws with a screwdriver before removing the lock from the door. If you have a mortise locking mechanism, there is a set screw that holds the handle to the spindle. Take off the doorknobs by removing this screw using the help of a screwdriver.

Remove the deadbolt as well as the latch plug from the door jamb. Then, you are able to install your new lock. If you're replacing a mortise you must measure the distance between your lock's case and your door's edge to make sure that the new lock is a good fit.

There are a variety of reasons that could prompt you to replace your door lock, such as suspecting that someone else has the key or if you're welcoming the arrival of a new roommate. You can save money by deciding to take the lock off yourself instead of paying an expert. It's much easier than people think and can be done in a matter of a few minutes.

Start by getting rid of the trim and handle from your door. Then, you can pry the trim away using a screwdriver that is flat. You should be able to twist off the majority of it. In some instances you might be able to remove the handles completely. Next, search for a pinhole on the inside of the handle and then insert an unstraightened clip into it. This will trigger the release mechanism, allowing you to take off the handle. Next, examine the inside of the lock to find a small tab that you can press with a flat screwdriver. After the spindle is removed, you are able to remove the cylinder and the housing.

Making a choice for a new lock

When it comes to selecting a new lock there are a lot of options. Take a look at various kinds of locks, and choose one that is compatible with the style of your door. Consider the backset which is the distance between the edge and the center of the hole for the lock. Also, consider the cross bore, a tiny hole that is located at the edge of your door's frame. Also, make sure to select a lock that is able to accommodate the door's thickness as well as swing.

Most door locks are evaluated by BHMA and the American National Standards Institute to provide you with an idea of how they will withstand use and how difficult to disable or pick. A grade 3 lock might be a good choice for a tranquil rural apartment complex, while a grade 1 lock might be more able to withstand the traffic that is frequented by a retail storefront on a busy street.

Most smart door locks require a digital code to open. If you're worried about security breaches or hacking, consult with an expert locksmith or your local police department for advice.

Replacing the cylinder

You can easily replace damaged or broken doors lock cylinder with an easy DIY project. It is important to select the right cylinder and follow the instructions. The first step is to remove the handle or knob in the event that one is present, then unscrew the trim that is attached to the base of the lock cylinder by using the aid of a screwdriver. After the trim has been removed, you can take off the screws holding the cylinder with the flathead. The cylinder can then be gently removed from the door.

Before you install the new cylinder, be sure that it is the right length for the door you are using. Take a measurement of the distance from the center to the right and left sides of the cylinder using a tape measure. Purchase a new cylinder which has the same measurements. This will prevent cylinders from snapping when doors are kicked or the key gets stuck inside.

Insert the replacement cylinder in the door and then turn the key. This will align the cylinder with your carrier which is located usually on the outside of the lock. Then, loosen the set screw which is supposed to be a couple of turns in the head. If there is a screw at the exterior of the case that is holding the door, you will have to loosen it.

After taking the lock cylinder out, you can replace it with the new lock by slipping the new cylinder into the case and tightening the set screw. You must also install the bracket that connects the cylinder with the stem for the lock indicator, which you can do by pulling out three small tabs on the back of the cylinder with needle-nose pliers. Attach the smaller bracket to the cylinder's back. You must then install the latch plate and strike plate, as well as the retaining rings connected to the top of the lock cylinder.

Installing a new lock

Start by measuring the width of your door if you are replacing a lock that is already in use. The majority of residential locksets come with a thickness of 3/8 to 1 3/4 inches. If your door is thicker you will require a door kit that is thick and includes longer screws, a longer tail piece (for door knobs) or spindle extensions (for deadbolts).

Most locks come equipped with a detailed installation guide to help you. Before you begin, go through the instructions to make sure you have followed all the steps. The guide will give you a good idea of the level of skill that is required to complete the task. It is possible to ask a friend who has had experience in changing locks for assistance if you are changing a lock the first time.

It's a good idea to cover the holes in the old hardware before installing the new lock. This will keep the screws from falling out of the holes and protect any tile you might have installed in the area. It also protects against potential damage from rust, dirt, and grime. SECURAM Touch includes a strip of masking or gaffer tape, however you can make use of any tape you have.

Once you've removed the screws that hold the interior portion of the lock section to the outside side then pull it out straight away. It's important to do this swiftly to avoid the lock from closing itself in a way that could end up harming the mechanism.

If your new lock has an latch bolt, install the new latch bolt into the upper cross bore. Make sure to place it in the correct location, which is marked by an arrow. Then, you can screw the latch plate onto the bolt.

Screw the deadbolt to the jamb on the door. Try the deadbolt a few times by throwing it to see if it extends into the strike plate. If you're using an electronic smart lock, be sure to follow the included instructions for programming it. This involves downloading an app and registering your email address, confirming your identity and connecting to the wireless network to connect your device.