Your Family Will Thank You For Getting This Replacing Upvc Window Handles Replacing uPVC Window Handles

It is simple to change the handles on windows made of upvc. The most important thing is to make sure that the replacement handle fits the spindle cut out in the window mechanism.

If the steps below are followed properly the cockspur handle will fit in most windows. The key is the step size of the handle.

What to look for

Over time, uPVC handles on many windows in the UK can start to show signs wear and wear and tear. When this occurs, the handle could become shaky or difficult to operate, making it essential to replace it. Anyone who is familiar working with basic hand tools can complete this relatively simple job.

The first thing to do is ensure that the handle is securely attached to the window frame and in a position that is open. The next step is to find the screws or pins which hold the handle. upvc door handles are typically located on the inside of the handle and can be removed using a screwdriver or pliers.

When the handle is loose and sagging, gently pull it back from its hinges. It is then necessary to find a new handle of the same style and size. This can be done in a DIY store or online. The process should take only five minutes and a screwdriver is all you need.

One crucial aspect to take into consideration when replacing the uPVC window handle is its step height. This is the distance between the handle's base and the place it sits in the frame of the window. This is usually an accepted measurement, however it is crucial to examine the step height of your existing handle prior to ordering the new one.

There are a variety of sizes based on the type of handle. Inline handles for uPVC windows typically feature lug centers of 31mm There are also cockspur handle types with 43mm centres. Tilt-and-turn handles are commonly found on uPVC Windows. They have a specific design which allows the window be tilted to allow for ventilation and then rotated to fully open the window.

The most frequent uPVC handle breakage is internal cracking instead of a break at the base. This can make them hard to open and is why it is essential to ensure that the replacement handle you buy has the same spindle length as your existing one.

Remove the handle that was previously used

If the handles on your windows are damaged or incorrectly fitted, they could cause double-glazed windows to close and open incorrectly. They may even get stuck. There are a variety of reasons, such as general wear and tear or the corrosion of the handle. In these situations it is crucial to find replacement handles made of upvc as soon as possible to avoid further damage and loss of function.

When replacing the handles of windows made of upvc and handles, it is important to remove the old handles from the window. Start by removing the screw by the handle while it is in the closed position. Once you have removed the screw, you are able to remove the handle. It is recommended to employ an electric screwdriver to accomplish this since it will make the task easier and quicker.

Be aware that screws could be hidden in plastic caps. It is best to remove the covers using the help of a Stanley knife. After removing the old handle, you'll need to check the square cutout on the base to make sure that the new handle you choose for the window lock is compatible. It is essential to measure the spindle length on the handle that was used and compare it to the dimensions of the window mechanism spindle cutout.

There are three kinds of upvc handles: Espag handles with a central screw that can be turned left or right and Cranked handles with two screws and Spade handles, which are made of flat arms and can be used either side of the upvc window. It is simple to replace the handle after you have identified one that is suitable. Just screw it into place, and ensure that the spindle is inserted correctly in the lock mechanism. After that, you can you can tighten the handle onto the window frame. The new upvc handles should now be secure.

Take a measurement of the Spindle

If you have to replace a upvc handle that has fallen, it's likely the spindle that holds it in place is damaged or is loose. In some instances, you can tighten the spindle by using a screw or pin. In certain situations, it may be necessary to replace the handle. There are a variety of upvc handles. There are three types of handles: inline espagnolette cockspur, and tilt-and-turn. Each handle type is installed and replaced in a different way.

It is crucial to measure the handle before buying a replacement. This will ensure that the handle will fit the window correctly and will be the right size. Luckily, all handles conform to industry standards for sizing, so it's relatively easy to identify the correct size.

To determine the size of your handle, first, remove it from the window by turning it back to the open position. Then, you should be able see the size of the screw or pin that is holding it. Then take the ruler or tape measure to determine the length of the spindle. Once you know the length of your spindle, it is possible to purchase a replacement of exactly the same size.

When you are looking to replace a handle, it is important to consider the step height of an window handle made of upvc. The step height is measured from the base to the point where the handle sits on the frame. Typically, this will be around 21mm for uPVC windows or 9mm for aluminum. Dropping objects into the space will allow you to determine how far the handle extends before it meets an obstruction.

Cockspur handles often have different backset heights depending on the type of window they are installed in. Inline espag handles have the standard height of 43mm centre to centre (2 fixing points). Cockspur handles have different backsets, based on the type of window they are located in. This is because they have a spur which extends from the handle and locks onto a cockspur wedge striking plate.

Install the new handle


After you have chosen the new handle, ensure that it is aligned with the holes for screws on the door. Secure it using the screws provided. Install the latch lever in the same manner as the handle on the main handle when you're replacing the door handle. Finally, reattach the door trim in order to conceal the screws for mounting and finish off your project.

Tip: To remove a metal head from a wooden wedge, place the handle on the floor so that its wide end is on the floor. Then use a hammer and tap the narrow end. Be careful not to damage the handle or spindle.