The Reasons Why Replacing Upvc Window Handles Has Become Everyone's Obsession In 2023 Replacing uPVC Window Handles

It is simple to change the handles on windows made of Upvc. The important thing is to ensure that the replacement handle fits the spindle cut out in the window mechanism.

If you follow the steps below any cockspur handle can fit in most windows. The step height of the handle is important.

What to Look For

A lot of windows in the UK come with uPVC handles and, over time, they can begin to show signs of wear and wear and tear. The window handle may become loose or difficult to operate when this occurs. This is a fairly simple job that can be accomplished by anyone who is comfortable with basic hand tools.

The first thing to do is ensure that the handle is securely connected to the window frame, and is in an open position. The next step is to locate the screws or pins that hold the handle. They are usually located on the inside face of the handle and can be removed with a screwdriver, or pliers.

When the handle has become loose It is best to gently pull it away from its hinges. It is then time to locate a replacement handle that is the same design and size. This can be done at an online store or in a DIY store. The process should take only five minutes and requires a screwdriver is all you need.

When replacing a uPVC handle, it is important to take into consideration the step height. This is the distance from the bottom of the handle until it sits on the window frame. It is generally an average measurement, but it is important to check the step height of your existing handle before ordering a new one.

Depending on the type of handle you are using there are various sizes to choose from. Inline handles for uPVC windows generally have lug centres of 31mm, and there are also cockspur handle types with 43mm centres. Tilt-and-turn handles are commonly found on uPVC windows. They have a specific design that allows the window to be slid down to let in air, and then turned to fully open the window.

The most common uPVC handle cracks are internal, instead of a break at the base. This can make it difficult to open. It is essential to make sure that any replacement handle has the same spindle that was used in your original one.

Remove the old Handle

A poorly installed or damaged window handles could cause your double-glazed windows to open or close in a way that isn't correct and may result in them getting stuck. There are a variety of reasons for this including general wear and tear or corrosion of the metal handle. In these situations it is crucial to locate replacement handles made of upvc immediately in order to avoid further damage and loss of functionality.

One of the first things that you should do when replacing window handles made of upvc is to remove the old handle from the window. To do this, begin by getting rid of the screw that is covered when the handle is in a closed position. After you have removed the screw, you are able to remove the handle. You can make the job simpler by using an electric screwdriver.

It is also important to note that the handles' screws could be hidden behind plastic caps, so it is recommended to use the Stanley knife to the screws and remove them. After removing the handle, you will need to check the square cutout on the base to make sure that the new handle you choose for the window lock is compatible. This is important because you'll need to measure the length of the spindle on the previous handle to ensure it is in line with the size of the window mechanism and the handle spindle that has been cut out.

There are three kinds of Upvc handles: Espag handles with a central screw that can be turned left or right and Cranked handles with two screws, and Spade handles which are made of flat arms and can be used on either side of the window made of upvc. It is simple to replace the handle once you've located one that is suitable. Just put it in place and ensure that the spindle is correctly inserted in the lock mechanism. After that then it is time to secure it to the window frame and your replacement window handles made of upvc should be secure.

Take a measurement of the Spindle

If you're replacing a Upvc window handle that has fallen off, it's likely due to the spindle that holds it in place has become damaged or loose. In certain situations, you can tighten the spindle with a screw or pin. In other situations, it will need to be replaced entirely. There are several kinds of window handles made of upvc. They include espagnolette handles that are inline or cockspur handles. They also have tilt and turn handles. Each type of handle is mounted and replaced in a different fashion.

Before purchasing a replacement handle it is essential to know the dimensions of the one you have. This will help ensure that the new handle is of the correct size and fits within the window. All handles are calibrated according to industry standards, making it easy to determine the right size.

To determine the size of the handle move the window to the open position. You should then be able to see the size of the screw or pin that holds it. Then take a ruler or tape measure to determine the length of the spindle. Once you know the length of the spindle you can purchase a new one that is the same length.

The step height of a window handle is also important to take into consideration when purchasing an alternative. The step height is the distance from the bottom of the handle until where it sits on the frame. Typically, door handles will be about 21mm for uPVC windows and 9mm for aluminium. To be sure that the new handle will fit it, you can drop something in the gap to determine the distance it will go before meeting an obstruction.

Cockspur handles often have different backset heights depending on the style of window they are installed in. Inline espag handles have a standard height of 43mm centre to centre (2 fixing points). Cockspur handles have different backsets, based on the window they are placed in. This is because they have a spur that extends from their handle and locks onto a cockspur wedge-striking plate.

Fit the New Handle

After you've chosen the new handle, ensure that it is aligned with the screw holes on the door. Secure it using the screws supplied. If you're also replacing the latch lever it can be put in similarly to the main door handle. Finally, reattach the door trim to conceal the mounting screws and finish the job.


Tips: To remove a metal head from a wooden wedge, place the handle on the floor so that its wide end is on the floor. Then use an hammer and tap the narrow end. Be careful not to damage the handle or spindle.