Five Laws That Will Aid In The Upvc Door Handle Replacement Industry Choosing the Right UPVC Door Handle Replacement

It's simple to replace your upvc handles, but choosing the right handle can be a challenge. Modern double-glazed handles are equipped with spring cassettes, but older handles don't.

If the handle made of upvc on your multipoint lock is sloppy and floppy, there may be an internal problem. This article will discuss several potential problems and their causes.

Handles that slide or drop

UPVC handles can withstand wear and tear, especially in older properties. A damaged spring cassette on the door lever is the most common cause of a floppy handle. This is caused by excessive force and the spindle that holds the cassette may be dislocated or turned round.

It is important to know that a uPVC handle replacement can be accomplished in a matter of minutes. The first step is to disassemble the handle unit that was previously installed by removing the fixing screws that are visible on the back of the handle lever plate. Once the handles are removed you can remove the cassette from the square spindle, and replace it with the new one.

You can find a vast selection of uPVC door handles to choose from on the internet and a lot of them are available in various finishes. Selecting the right finish will determine the length of time your handle will last and how easy it is to keep clean. Finishes such as Resista, Stainless Steel, or PVD are designed to resist corrosion and last up to 25 years.

After selecting a colour or design, you can select the kind of handle you require. The most popular are lever and pad arrangements. Lever pads are often used to prevent unauthorised access. They have a lever inside and a paddle outside.

Then, take a measurement and note the dimensions of the handle you have. You will need to measure the PZ dimension which is the distance between the screw hole and the middle of your lever. You'll also need to know how long the handle is as well as the size of its keyhole. Once you know the measurements, you can compare them to the handle size matrix to find the correct replacement.

Broken springs

Over time, uPVC handles may become wobbly or loose. The spring cassette could also break. These springs are used to align the handle lever in a horizontal direction. Without them, your doors will not lock properly.


Modern uPVC handles come with these cassettes incorporated directly into the back plate. However, older uPVC doors typically have these springs built into the actual lock mechanism. This isn't something you can be fixed by yourself but it is worth getting your locksmith to take a look at as this could be the reason behind the drooping or sagging uPVC door handles.

The most common issue associated with uPVC handles is that they become loose as time passes. This is usually caused by worn-out springs, which are easy to repair. This is usually caused by excessive handling of the handle. The square spindle in the handle will wear down and cause the springs to move.

To solve this issue, you'll need open the door to the handle plate and then remove all the screws. This can be accomplished using the Philips screwdriver. Once the screws are removed the handle can be removed and the plates pulled apart carefully. The old springs can be removed and replaced with new ones.

Depending on upvc door handles of handle you have the distance between the two fixing screws can vary and this is essential to know before buying an alternative. This measurement is known as the PZ measure. It is recommended that this is done using a calibrated tape measure for accuracy.

After reinstalling the springs, you should be able to use the handle without any issues. It is recommended to lubricate your internal mechanism to make sure that everything is functioning just as it should. This will not just ensure that your uPVC doors are as secure as possible but will also make them more comfortable to operate over time too.

Handles that slide around

Handles that slide could be caused by a variety of factors. One of the most frequent causes is when the levers of the handle aren't aligned with the lock. This can happen with both uPVC and composite doors, but it is generally more noticeable on older doors as they are typically made of cheaper materials that don't resist the elements.

A professional can address this issue by re-aligning the handles so that they are aligned with the lock. They'll also inspect the lock to determine what requires fixing. In many cases, a slight adjustment to the springs of the handle can fix the issue.

It's easy to replace your uPVC handle however, you must measure the existing handle to ensure that the replacement is the correct size. You'll need to determine the distance between the two fixing screws and the dimensions of the lever as well as the key-hole position. You can then use this uPVC handle size guide to locate the correct replacement for your home.

Once you have the measurements The next step is to eliminate the old uPVC handles. It's usually a straightforward procedure that requires only the use of a screwdriver. Once the screws have been removed, you can then remove the handle and then proceed to install the new one.

Before you start, it's worth ensuring that the door is securely open using a wedge to stop it from closing in the middle of your work. After the handle has been removed it is now possible to access the underlying parts of the door to fix the problems that are causing it to slide.

A handyman from Fantastic Services will be able to assist you if want to tackle the task yourself or lack the nerves. They will employ specialist locksmith opening techniques to unlock the door without causing any damage and then replace the handle that is damaged and make sure that everything is in place and functioning exactly as it should.

Gearbox damage

A damaged gearbox may cause the upvc door handle to become stiff or lose its functionality. This can also prevent the lock from being able to be opened with keys. This can be dangerous and should be addressed as soon as possible. It is important to call a locksmith if you are unable to solve the issue yourself. They have the tools and know-how to do the job right.

The first step is to remove the handle from the cover plate. This can be done using an instrument that has an angled tip. After removing the handle, you need to remove the middle screw which holds the barrel. Once you have removed the middle screw, you can then loosen the two screws that hold the barrel. Then, you can pull the barrel from the door. To do this, you will need someone to hold the door open.

After removing the cylinder, you can replace with a new cylinder. Make sure the new cylinder has the same size as your old one. You may end up with an improperly aligned handle. This can lead to a number of problems such as leaks and drips.

Many upvc doors have adjustable slots that can be used to tighten or loosen the handle. They are typically located on the inside of the door, near where the handle joins the cylinder. Allen wrenches can be used to tighten the adjustment slots. After you have made the adjustments, you can put the handle back on and screw it back in. You can then test the handle and ensure it works correctly.

The door handle made of upvc that becomes floppy when closed is usually an indication that the gearbox or internal spring components have failed. This could cause your multipoint locks made of upvc to fail leaving your door open to burglars. If this occurs, it is necessary to replace the gearbox. This will cost between PS145 - PS280 inclusive of labour.