The Under-Appreciated Benefits Of Kia Picanto Key Fob Replacement How to Replace a Kia Sportage Replacement Key

For many Kia models keys, there is a built-in keyless entry system. This key is similar to a remote control and is exchangeable by a Kia dealer.

Key fobs might stop working due to a variety of reasons, including the battery of the coin is dead, worn buttons signals, signal interference, water damage, and a defective receiver module. Here are some helpful tips to help you get your Kia sportage replacement key to work once more.

How to replace the remote key or smart key?

The battery in your Kia's intelligent key will eventually have to be replaced, whether it's a remote, a push-to-start key or a normal metal key that doesn't have transponder. This is especially when the car displays a message that the smart or remote key has low battery power.

This is a relatively simple procedure. To replace the battery on the keyfob, remove your mechanical key from the slit at the back of the fob. Then, pull the cover off. A small screw is located inside the key fob to hold the battery in place. Utilizing a small screwdriver remove the screw and pull out the old battery. Install the new battery and then close the opening on the key fob.


Test the key fob by pressing the lock/unlock buttons. If the doors unlock and lock in the same way, you're set! You can now make use of your Kia's hands-free lock/unlock feature when your fingers start to get cold or you have to run some errands in Brandon.

Note: Some key fobs may need to be programmed (transponder chips or smart keys). This requires a machine for programming which is available to the automotive locksmith or dealer. Other keys (non-transponder metal keys) do not require programming. If you're looking to reprogramme your key, you'll need to record the key code number on the key code tag.

How do you replace the battery?

If the Kia key fob is unable to respond to pressing the lock or unlock button, it is likely that the battery is not fully charged. A low battery may cause other issues, such as the check engine light turning on or the engine not turning properly. It is relatively easy to replace the key fob battery with just some tools.

Before starting the process before beginning the process, ensure that your vehicle is off and all doors are shut. Find the small metal or plastic piece that is on the bottom of your key fob and play with it until a metallic key pops out. Then, kia picanto spare key can put the key into the driver's door handle to unlock your car.

To replace the key fob battery, take off the cover on the rear and use a plastic bar tool to remove the latch that holds the black negative battery cable. Remove the old battery and align the new one to ensure that the "+" positive side faces you, while the "negative" negative side is facing towards the fob's metal electrical contacts. Push the new CR2032 battery straight into place with care to avoid using too much force to avoid bending or damaging the contacts on the metal.

After installing the new battery after which you turn the key fob on and off in the ignition until the door locks cycle. You can then test your Kia's keys fob again to confirm that it's working properly.

How to replace a smart keys

There is a possibility of having a standard keyfob, or a Smart Key based upon the model of Kia Sportage. The smart key comes with an embedded mechanical key blade however, the standard key fob does not. Both key fobs contain batteries that will eventually require replacement. This is a straightforward process that takes only two minutes.

Be sure to switch off your Kia and stand on a flat, well-lit surface before you begin. Be aware that there are small parts inside the fob that can be removed if not vigilant.

The first step is to find the small release button that is located on the back of the lower part of the fob. It could be an oval or circular slot. After pressing this button button, the mechanical blade will pop out and you will be able to open the key fob.

After the key fob has been removed, you can remove the battery that was in it. The new battery is the CR-2032, and it can be bought on the internet or at your local auto parts store. When you are done with the battery, you should be able to lock, unlock and start your vehicle with your key fob even if the engine isn't running!

How do I replace a mechanical key

The Kia keyfob is an excellent convenience, allowing us to lock or unlock our car simply by pressing a button. As with all devices, the Kia key fob can occasionally have problems. Luckily, there are ways to resolve these issues and ensure that our key fobs are in good working condition for the long run.

One of the most frequently encountered problems is a low or dead battery. The battery could cause the device to stop working or work intermittently. If this is the case try replacing the battery with a new one.

If this doesn't resolve the problem Try using a standard flat-head screwdriver to break open the fob's plastic casing. Be careful not to damage internal components or scratch the plastic. Once open, carefully remove the battery you have been using and replace it with a new one.

After the new battery has been put in, close and open the doors with the mechanical key (every Kia fob has an emergency mechanical key that will fit into the slot). Test the key fob to verify that it's working properly. If the fob still isn't working, call an authorized locksmith or dealer to help resolve the problem. Make sure they make you an emergency key that works across all trunk and door cylinders in order to avoid future lockouts.