10 Best Facebook Pages Of All Time About Repair Car Keys How to Repair Car Keys


The car keys aren't big and may not seem important, but they are essential for the operation of your vehicle. Replacing a traditional key or a transponder one could cost as much as $200.

There are methods to repair your car keys at home with a fraction of the cost. This article will discuss the most frequently encountered car keys problems and their DIY solutions.

Dead Key Fob Battery

Cars are equipped with a remote key fob that allows opening the doors and trunk easier than ever before. The battery in the device is prone to dying. However, there are some tricks you can employ to resolve this issue in a pinch.

Check to see if your vehicle is still in ignition mode. If so, the key fob's battery may be low, but not dead. To test this, press the button on the fob against the ignition button on the vehicle. If it works, the battery is probably fine and only requires to be replaced.

To replace the fob battery, begin by prying open the case with the help of a screwdriver or watch-type device. Be cautious not to press too hard since this could cause the fob to split apart. If the fob isn't opening open with ease, try placing your pry tool in more than one place around the outside of the case.

Once the fob is opened take out the mechanical key and then open the electronic portion of the car. Insert the new battery and snap it back into the shell. If the key fob doesn't work after this procedure, there could be a bigger problem with your car's remote start system that requires a professional diagnosis. If this is the case, a reputable mechanic should be able help you. You can also contact roadside assistance for assistance with your vehicle, if you require it.

Broken Key Ring

There are a few things you can do in the event that your key fob won't work because the ring is broken. First, you must check to see if the damaged piece is still in the ignition. If it's still in there, remove it without causing damage to the ignition lock or the door lock. If you're having difficulty taking it off, call a locksmith for help. They have specialized tools that can safely remove keys that are damaged from the ignition.

Another reason that can lead to the car key breaking is corrosion on the circuit board or frame. You can clean the board with rubbing alcohol and a cotton swab. This will remove corrosion and ensure that the contact pads don't become damaged.

If your key isn't working because the ring broke or was damaged, you might be able to fix it with a strong wire or nail to plug the hole. Superglue can be used to fix the broken key ring. After cleaning the ring with a wet cloth apply a small amount of superglue to the ends of the wire or nail. Let the pieces dry and then press them together. These DIY solutions may sound appealing, but they are only temporary solutions. It is recommended to hire an expert locksmith for repairs that last. They have the tools and knowledge to fix a broken car key quickly and efficiently. They can even replace the battery inside your key fob, and modify it if necessary.

Broken Key Blade

Some key blades may break due to wear and tear. If this happens, it's time to get a new key. This problem isn't nearly as serious as you think at first glance. The problem is that the blade has broken off from the case.

Spraying key fob repair near me into the keyhole is one method to repair it. Then, you can employ pliers or tweezers grasp the damaged end of the key and pull it. You could also make use of a magnet if the key is magnetic. Use a magnet to assist you remove the key, but be cautious to not sever the tumbler of the lock.

If you are unable to take the broken piece of the key, contact an expert locksmith immediately. They have the right tools to safely remove keys without causing further damage.

You can also use super glue to fix a broken key. Apply a small amount glue to the edges of the break and press them together. Make sure the glue is dry before inserting the key into the lock. This method is not very reliable, and you might have to repeat it several times before it works. Super glue might not be able to hold the key in place. This is more of a temporary solution than a permanent solution.

Broken Plastic Loop

If your key fob's plastic loop breaks off it can render the key ineffective. It's a fairly simple fix. You can make use of wire or a nail for finishing as a replacement. Make two holes in the damaged loop of plastic at each end of the nail or wire. Cut the wire or nail into a key width, then place tiny drops of superglue into each hole. Then, press the wire or nail into the holes and let them dry.

A locksmith who sells replacement shells is an alternative option. They can take out the programmable part of your key, then transfer it to the new shell and cut an entirely new blade for less than a full replacement cost.

It's not the most ideal solution, but it'll bring you back on the road if your key snapped in half. However, it can be difficult to repair the key blade if it is in the ignition. If you are not careful you could make use of a hair clip or a needle to take the broken part from the ignition. Contact a locksmith who has special tools to safely remove broken keys from ignitions. You can also request a new key that is made using the correct cuts to fit the ignition of your car.

Broken Master Key

You'll need to try in vain to recover the key before it is completely destroyed. You can employ lubricants, tweezers, and needle nose pliers for grabbing the broken fragment of a key.

Spray the inside of the lock with WD-40 or a graphite powder. You can also employ the hacksaw blade technique that involves sliding the blade along the sides of the broken key, and grabbing onto some of its 'teeth.' If you are successful you will be able to take the broken key out.

Many hardware stores carry the spiral key extraction tool. It is a thin, flexible bar with spiral threads, which can be put into the keyway, and then bent to get into the broken part of the key. Once it is hooked to the serrations, you can turn it in a circular direction and push it against the damaged section of the key to get it out.

It's worth trying to remove the master key that is broken before calling a professional locksmith. If you can't get the piece out, you need to call the big guns to have a locksmith cut you a new key and reprogram it with the transponder in your car.